User manual ALPINE VPA-B222

[. . . ] R Vehiclehub Pro EN VPA-B222 FR · OWNER'S MANUAL Please read before using this equipment. · MODE D'EMPLOI Veuillez lire avant d'utiliser cet appareil. · MANUAL DE OPERACIÓN Léalo antes de utilizar este equipo. ES ALPINE ELECTRONICS MARKETING, INC. 1-1-8 Nishi Gotanda, Shinagawa-ku, Tokyo 141-0031, Japan Phone 03-5496-8231 ALPINE ELECTRONICS OF AMERICA, INC. [. . . ] for at least 2 seconds after selecting a desired band. The FUNCTION screen is displayed. Press the joystick up or down to select PRESET MEMORY, then press the joystick right. Press the joystick up or down to select any one of the preset numbers PRESET1 through PRESET6, then press / /ENTER. The selected station is stored. 3 4 Checking the SAT Radio ID Number A unique Radio ID number is required to subscribe to SAT Radio programming. Each third party XM or SIRIUS radio comes with this number. XM Radio: Repeat the procedure to store up to 5 other channels onto the same band. To use this procedure for other bands, simply select the desired band and repeat the procedure. A total of 18 channels can be stored in the preset memory (6 channels for each band; XM-1, XM-2 and XM-3 or SIRIUS-1, SIRIUS-2 and SIRIUS-3). This number is an 8 character alphanumeric number. It is printed on a label found on the SAT Receiver. SIRIUS Radio: · If you store a channel in a preset already being used, the current channel will be replaced with the new one. This number is a 12 character alphanumeric number. It is printed on a label found on the SAT Receiver. It can also be displayed on the screen of the VPA-B222 in the following way. Receiving Stored Channels 1 2 3 4 1 2 3 4 Press / /ENTER to select the channel number turing mode. While receiving a SAT Radio band, press or to select channel "0" for XM, or to select channel "255" for SIRIUS. To cancel the ID number display, change the channel. Press and hold for at least 2 seconds repeatedly until the desired band is displayed. for at least 2 The FUNCTION screen is displayed. Press the joystick up or down to select PRESET CALL, then press the joystick right. Press the joystick up or down to select any one of the preset numbers PRESET1 through PRESET6, then press / /ENTER. The selected station is received. or . · You cannot use "O, " "S, " " I, " or "F" for the ID Number. (XM radio Receiver only) · You can check the ID number printed on a label on your third party, SAT Radio Receiver package. · During reception, you can change the station by pressing 24-EN Category/Channel Search Function You can search for programs by Category or Channel name. iPod® (Optional) 1 2 1 1 2 Press /MENU/FUNC. . The Category Search screen is displayed. Press the joystick up or down to select your desired category. Joystick To receive the category directly Press / /ENTER. The first channel of the selected category is tuned. To search for a channel in the category Press the joystick right to change to the channel search mode of the selected category . Press the joystick up or down to select a channel, then press / /ENTER. The selected channel is received. An iPod® can be connected to the VPA-B222 by using the proprietary ALPINE FULL SPEEDTM Connection Cable (KCE-422i). When the VPA-B222 is connected by using the cable, the controls on the iPod are not functional. About iPod usable with this unit Storing Weather or Traffic information from SAT Radio 1 2 While receiving weather or Traffic information in the SAT Radio mode, press and hold /MENU/FUNC. for at least 2 seconds. The FUNCTION screen is displayed. The unit can be used with third generation and above iPod, iPod photo, iPod minis or iPod nano. · Touch wheel or scroll wheel type iPods without the dock connector cannot be connected to the unit. · The unit can be used with the following iPod versions. Correct function of earlier versions cannot be guaranteed. Third generation iPod: Ver. 1. 0 Press the joystick up or down to select WEATHER MEMORY, then press / /ENTER. The received weather or traffic channel is stored. · The unit cannot be used with the software versions earlier than 2005-02-22. [. . . ] · Be sure to turn the power off on the unit before changing the switch position. Rear output Terminal Use when connecting an amplifier or equalizer. Front output Terminal Use when connecting an amplifier or equalizer. Ai-NET Connector Connect this to the output or input connector of other product (CD changer, Equalizer, etc. ) equipped with Ai-NET. Guide Output Terminal If an external audio processor is connected, outputs the navigation interrupt voice signal that is input from the Alpine navigation system, or the speaker input terminal. Commander Terminal iPod Direct Connector Control iPod signals. Connect this to an iPod, using the (also separately sold) FULL SPEEDTM Connection Cable (KCE-422i). ALPINE/OTHER switching button Set to "ALPINE" for normal use. Set to "OTHER" when connecting optional display interface box. 53-EN System Example Connect the ALPINE Monitor Monitor (Sold Separately) RGB Input Terminal RGB Cable (Included) Monitor B. Box (Sold Separately) Display Output (RGB Output) Terminal Connect a 13P RGB terminal equipped monitor using the RGB cable supplied with the unit. RGB Cable (Included) Connect a Monitor of another manufacturer Monitor (Sold Separately) Video Input Terminal Monitor B. [. . . ]