User manual ALTEC LANSING 806A HF DRIVERS

[. . . ] Micro sistemi 806A HF DRIVERS composto da 806A HF DRIVERS (apparecchio principale) e CP-MP40H (sistema di diffusori). 806A HF DRIVERS micro systeem bestaande uit 806A HF DRIVERS (hoofdtoestel) en CP-MP40H (luidsprekersysteem). 806A HF DRIVERS Sistema de Micro Componente composto de XLMP50H (unidade principal) e CP-MP40H (sistema de alto-falante). 806A HF DRIVERS Micro Component System consisting of 806A HF DRIVERS (main unit) and CP-MP40H (speaker system). DEUTSCH Siehe Seiten i bis x und D-1 bis D-32. [. . . ] Supplied AM loop aerial: Connect the AM loop aerial to the LOOP socket. Position the AM loop aerial for optimum reception. Place the AM loop aerial on a shelf, etc. , or attach it to a stand or a wall with screws (not supplied). Left speaker FM aerial Installing the AM loop aerial: < Assembling > < Attaching to the wall > Wall Screws (not supplied) External FM aerial: Use an external FM aerial if you require better reception. Consult your dealer. External FM aerial Wall socket (AC 230 V, 50 Hz) White line Plain Preparation for Use Right speaker Note: Placing the aerial on the unit or near the AC power lead may cause noise pickup. Place the aerial away from the unit for better reception. 8 E-6 05/3/24 806A HF DRIVERS(H)E1. fm TINSZA054SJZZ 806A HF DRIVERS System connections (continued) !Speaker connection Connect the wire with the white line to the minus (-) terminal and the plain wire to the plus (+) terminal. Caution: " Do not let the bare speaker wires touch each other. " Use speakers with an impedance of 4 ohms or more, as lower impedance speakers can damage the unit. " Do not mistake the right and the left channels. The right speaker is the one on the right side when you face the unit. ENGLISH !AC power connection After checking all the connections have been made correctly, connect the AC power lead to the AC power input socket, then plug the AC power lead of this unit into the wall socket. Incorrect 15 Preparation for Use Placing the speaker system: The left and right speakers have individual shapes. battery Remote sensor 0. 2 m - 6 m (8" - 20') Preparation for Use Check the remote control after checking all the connections (see pages 6 - 7). Point the remote control directly at the remote sensor on the unit. ALTEC LANSING TINSZA054SJZZ (H) 8 E-8 05/3/24 806A HF DRIVERS(H)E1. fm TINSZA054SJZZ 806A HF DRIVERS Sound control !Adjusting the volume Main unit operation: When the VOLUME control is turned clockwise, the volume will increase. When it is turned anti-clockwise, the volume will decrease. Remote control operation: Press the VOLUME (- or +) button to increase or decrease the volume. ENGLISH 01 2 . . . . . Adjusting the bass Basic Operation Main unit operation: 1 Press the BASS/TREBLE button to select "BASS". 2 Within 5 seconds, turn the VOLUME control to adjust the bass. Remote control operation: 1 Press the BASS/TREBLE button to select "BASS". 2 Within 5 seconds, press the VOLUME (- or +) button to adjust the bass. -3 . . . 0 . . . 4 !Adjusting the treble Main unit operation: 1 Press the BASS/TREBLE button to select "TRE". 2 Within 5 seconds, turn the VOLUME control to adjust the treble. [. . . ] If such a problem occurs, do the following: 1 Set the unit to the stand-by mode and turn the power on again. 2 If the unit is not restored in the previous operation, unplug and plug in the unit, and then turn the power on. Note: If neither operation above restores the unit, clear all the memory by resetting it. Maintenance !Cleaning the CD pickup lens Do not touch the laser pickup lens. [. . . ]