User manual ALTEC LANSING 9842-8A SPEAKER SYSTEM

[. . . ] DE Running the dryer with door open dF Invalid door state for more than 256 milliseconds. Invalid state of key circuit short for 30 secs bE2 FE Invalid power source Frequency 2E Electronic Control Problem (Over Voltage Error) Electronic Control Problem (Communication Error) Invalid state of Eeprom communication A Communication error between the WIFI PBA and the MAIN PBA A Communication error between the DR Modem and the MAIN PBA A Communication error between the LCD PBA and the MAIN PBA Invalid heating Temp in running the dryer AE Et AE4 AE3 AE5 HE 2 Technical_information-02835D-02_EN. Indd 2 2012-04-26 11:51:29 ALIGNMENT AND ADJUSTMENTS WARNING To avoid risk of electrical shock, personal injury or death; disconnect power to dryer before servicing, unless testing requires power. TEST MODE Service Mode * If "AE3" or "AE4" error occured, press the Start button then error will be cleared. [. . . ] - If press Temp key In Software Version Mode, it will return Service Mode. DV457* - If the unit enters service mode, the software version is displayed in the center top of the display panel. If you press the “2” button, the software version of the sensor board is displayed. 4 Technical_information-02835D-02_EN. Indd 4 2012-04-26 11:51:30 ALIGNMENT AND ADJUSTMENTS WARNING To avoid risk of electrical shock, personal injury or death; disconnect power to dryer before servicing, unless testing requires power. Data Display Mode How to Enter: DV455* - If you press the time button in service mode, the mode changes to data display mode. Definition of Data Display Mode: - Display Mode 1 : Temperature data - Display Mode 2 : Average Touch Sensor data for 1 minute - Display Mode 3 : Average Temperature data for 1 minute DV457* - If you press the “5” button in service mode, the mode changes to data display mode. - If you press the up arrow button, the display mode increases. - If you press the down arrow button, the display mode decreases. Definition of Data Display Mode: - Display Mode 1 : Temperature data - Display Mode 2 : Average Touch Sensor data for 1 minute - Display Mode 3 : Average Temperature data for 1 minute 5 Technical_information-02835D-02_EN. Indd 5 2012-04-26 11:51:30 ALIGNMENT AND ADJUSTMENTS WARNING To avoid risk of electrical shock, personal injury or death; disconnect power to dryer before servicing, unless testing requires power. Caution for the Repair and Replacement Please follow below instruction for the trouble diagnosis and parts replacement. 1) As some electronic components are damaged by the charged static electricity from the resin part of dryer or the human body, prepare the human body earth or remove the potential differ ence of the human body and dryer by contacting the power supply plug when the work contacting to PCB is executed. B assembly is designed for no trouble, do not replace the P. B assembly by the wrong diagnosis and follow the procedure of the trouble diagnosis when the micom is not operated normally. 8 Technical_information-02835D-02_EN. Indd 8 2012-04-26 11:51:31 TROUBLE SHOOTING WARNING To avoid risk of electrical shock, personal injury or death; disconnect power to dryer before servicing, unless testing requires power. No Problem What To Do • • • • 1 Will Not Start or Run • • • • • • • • • • • • • • • • • 5 Blows fuses or trips circuit breaker (Gas Model) All wires are hooked up to their corresponding terminals. Check for error code 3 (See Table for codedefinition). Belt off or broken and Belt Cut-off Switch operates. (Rotor winding , stator winding , generator) Is the motor protector normal?If above points are not found, the PCB assembly is out of order. [. . . ] thumping Check for loose tumbler baffle , rear tumbler roller(s) worn or misaligned , out-of-round tumbler or high weld seam on tumbler. Ticking Check for loose wire harness or object caught in blower wheel area. Scraping Check for front or rear bulkhead felt seal out of position or worn tumbler front bearings. 9 Igniter glows - No gas ignition 10 The gas is ignited but the flame goes out 11 Improper drying clothes wrinkled Rough texture long dry time 12 Noisy and/Or Vibration • • • 10 Technical_information-02835D-02_EN. [. . . ]