User manual ALTEC LANSING 9843 SPEAKER SYSTEM

[. . . ] HE dE dF Invalid door state for more than 256 milliseconds bE2 Invalid state of key circuit short for 30 secs FE Invalid power source Frequency 2E Electronic Control Problem (Over Voltage Error) Electronic Control Problem (Communication Error) Invalid state of Eeprom communication AE Et 2 (Technical)DV405-02365H-02_EN. Indd 2 2012-06-19 1:25:53 ALIGNMENT AND ADJUSTMENTS WARNING To avoid risk of electrical shock, personal injury or death; disconnect power to dryer before servicing, unless testing requires power. tEST MODE Service Mode (DV405 , DV395 , DV393 only) How to enter: - To enter Service Mode , press Mixed Load Bell + Temp. Keys 3 seconds in normal mode until it sends out a beeping sound. [. . . ] - If press Temp key In Software Version Mode, it will return Service Mode. Indd 3 2012-06-19 1:25:53 ALIGNMENT AND ADJUSTMENTS WARNING To avoid risk of electrical shock, personal injury or death; disconnect power to dryer before servicing, unless testing requires power. Continuous Run Mode Power On state (Normal user mode) Mixed Load Bell +Dry Level(DV405, DV395, DV393) or Wrinkle Prevent + Time(DV231, DV365) 7 SEC Continuous Run Mode How to enter: - - - - Press Mixed Load Bell +Dry Level(DV405, DV395, DV393) or Wrinkle Prevent + Time(DV231, DV365) for 7 sec during Power On State (normal user mode). Once in Continuous Run Mode, display “cc” for 1 sec and finished cycle count for 1 sec and the remaining time for 1 sec in turns. The previous cycle will restart during Continuous Run Mode until the mode is deactivated. During Continuous Run Mode, press Mixed Load Bell +Dry Level(DV405, DV395, DV393) or Wrinkle Prevent + Time(DV231, DV365) for 7 seconds to go back to normal user mode. Data Display Mode (DV405, DV395, DV393 only) How to Enter: - With Power On, press AdjustUp Key + AdjsutDown Key for 7 seconds until it sends out a beeping sound . - If not pressed any keys for 5 minutes, it will be set back from Data Display Mode - If pressing AdjustUp Key in this mode, Display Mode will be incresed. - If pressing AdjustDown Key in this mode , Display Mode will be decresed. Definition of Data Display Mode: - Display Mode 1 : Temperature data - Display Mode 2 : Average Touch Sensor data for 1 minute - Display Mode 3 : Average Temperature data for 1 minute 4 (Technical)DV405-02365H-02_EN. Indd 4 2012-06-19 1:25:53 ALIGNMENT AND ADJUSTMENTS WARNING To avoid risk of electrical shock, personal injury or death; disconnect power to dryer before servicing, unless testing requires power. € Exhaust too long, too many elbows, flex ductwork installed. Dry time • Blower impeller bound; check for foreign material in blower area. € Clothes too wet due to insufficient spin out by washer. • Thumping Check for loose tumbler baffle , rear tumbler roller(s) worn or misaligned , out-of-round tumbler or high weld seam on tumbler. € Ticking Check for loose wire harness or object caught in blower wheel area. Noisy and/Or 12 • Scraping Check for front or rear bulkhead felt seal out of Vibration position or worn tumbler front bearings. Indd 7 2012-06-19 1:25:54 TROUBLE SHOOTING WARNING To avoid risk of electrical shock, personal injury or death; disconnect power to dryer before servicing, unless testing requires power. ς Lamp resistance 80~100 Ω (Violet & gray) Thermostat 3 Thermostat 2 Heater  160 °C, 25A thermal cut-off 127/99 °C, 25A Hi-limit 240V/5300W Motor (Electronic & GAS) Contacts 1M 2M 3M 5M 6M  Measure resistance of the following terminal 1) Door switch : off Terminal : “COM” - “NC” (1-3) < 1Ω Terminal : “COM” - “NO” (1-2) : ∞ Ω 2) Door switch : On Terminal : “COM” - “NC” (1-3) : ∞ Ω Terminal : “COM” - “NO” (1-2) < 1Ω Function Start Run  = Contact closed Centrifugal Switch (Motor) 2. Indd 8 2012-06-19 1:25:57 TROUBLE SHOOTING WARNING To avoid risk of electrical shock, personal injury or death; disconnect power to dryer before servicing, unless testing requires power. Indd 9 2012-06-19 1:25:58 TROUBLE SHOOTING WARNING To avoid risk of electrical shock, personal injury or death; disconnect power to dryer before servicing, unless testing requires power. rY7 Sensor Bars & temperature sensor check Sensor Bars - Disconnect harness and test Pink wire Pin 4 to Orange wire Pin 5. [. . . ] If converting from a 4-wire electrical system to a 3-wire, the ground strap must be reconnected to the terminal block support to ground the Dryer frame to the neutral conductor. External ground connector Green or bare copper wire of power cord ¾” (1. 9 cm) UL-listed strain relief Center silver-colored terminal block screw Neutral Grounding wire (green/yellow) Neutral wire (white or center wire) 1. Remove the External ground connector screw. [. . . ]