User manual ALTEC LANSING M302

[. . . ] Altec Lansing Moondance Home Digital Speaker System and Alarm Clock for iPod® M302 User Guide Welcome Thank you for purchasing the Altec Lansing Moondance Home speaker system. Designed specifically to work with your iPod, this system provides high-quality audio and radio performance that brings out the best in your music. This Altec Lansing speaker system is designed to work with: · iPodtouch · iPodnano(3rdgeneration) · iPodclassic · iPodnano(2ndgeneration) · iPodwithvideo · iPodnano(1stgeneration) · iPodwithcolordisplay · iPodmini FCC Compliance Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate this equipment. ThisdevicecomplieswithPart15oftheFCCRules. Operationis subject to the following two conditions: 1)Thisdevicemaynotcauseharmfulinterference, and 2) hisdevicemustacceptanyinterferencereceived, including T interference that may cause undesired operation. Please carefully read this User Guide for instructions on setting up and using your speaker system. [. . . ] If the system isn't on, press the STANDBY button on the speaker system or the button on the wireless remote. PresstheSOURCEbuttononyourspeakersystemortheSOURCE buttononthewirelessremoteuntiltheFMappearsontheLCD. Tune to the station you want to listen to. buttons on the wireless remote to tune in the How to Store Preset Stations Your Altec Lansing Moondance Home speaker system's wireless remote enablesyoutoprogramupto16FMstationpresets: 1 2 3 4 Ensure your speaker system is powered on. Make sure you are in "FM" mode. PresstheENTERbuttononthewirelessremote. Apresetlocation will show and begin to flash. The station stored in that preset will be displayed in the lower right-hand corner of the LCD display. UsetheVOLUME+and­VOLUMEbuttonsonthewirelessremote to select the preset location you want to store the station in. PresstheENTERbuttontostorethestationinthepresetlocation. YoucanstoreoneFMstationineachpresetlocation. Pressandholdthesesamebuttonsfor3secondstofindthenext clearFMstation. PressandholdtheAUTObuttononthewireless remotefor3secondstoautomaticallytuneandsaveallclearFM stations. 5 1 2 3 4 To store other preset stations, repeat the above steps. How to Recall Preset Stations Ensure your speaker system is powered on. Make sure you are in "FM" mode. buttons on the wireless remote to select 6 Adjust the volume. UsetheVOLUME+and­VOLUMEbuttonsontheAltecLansing MoondanceHomespeakersystemtoadjustthesystemvolume. Or, usetheVOLUME+and­VOLUMEbuttonsonthewirelessremote. NOTE ExtendtheFMantennawirefullyforbestFMreception. Also, donot strip, alter or attach to other antennas. The radio will tune to your preset station. 12 Listening to a Non-docking iPod or Other Portable Audio Device Ifyouhaveanon-iPodMP3playerorothernon-dockingportableaudio device, you can enjoy it through your Altec Lansing Moondance Home speakersystemaswell. JustconnectitviatheAUXINjack. Here'show: 7 Adjust the volume. UsetheVOLUME+and­VOLUMEbuttonsontheAltecLansing MoondanceHomespeakersystemtoadjustthesystemvolume. Or, usetheVOLUME+and­VOLUMEbuttonsonthewirelessremote. 1 2 Locate a 3. 5 mm stereo cable (not included). Plug one end of the stereo cable into your device. Your device should have either a headphoneorLINEOUTjackforyou to plug into. NOTE You may need to adjust the device volume also. Your device's volume should be set to approximately ¾ volume. 8 When you are finished listening to your portable audio device, please remember to turn both it and your speaker system off to conserve electricity. 3 Plug the other end of the stereo cable into your speaker system's AUX IN jack. TheAUXINjackislocatedonthebackoftheunit. Ensure your speaker system is powered on. If the system isn't on, press the STANDBY button on the speaker system or the button on the wireless remote. 4 5 6 Select "AUX" mode. PresstheSOURCEbuttononyourspeakersystemortheSOURCE buttononthewirelessremoteuntiltheAUXappearsontheLCD. Turn on your device and start it playing. 13 Setting the Clock Display How to Set the Clock Time and Date 6 Set the date. [. . . ] What Will Altec Lansing Do to Correct the Problem?Altec Lansing will, at its option, repair or replace any product that proves to be defective in material or workmanship. If your product is no longer being manufactured, or is out of stock, at its option, Altec Lansing may replace your product with a similar or better Altec Lansing product. How to Get Warranty Service To get a covered product repaired or replaced, you must contact Altec Lansing during thewarrantyperiodbyemail(csupport@alteclansing. com). Youmustincludeinyour email, your name, address, email address, telephone number, date of purchase and a complete description of the problem you are experiencing. [. . . ]