User manual AMERICAN AUDIO V4000 PLUS

[. . . ] Professional Power Amplifier MONO STEREO BRIDGE POWER ON LIMITER ON OVER HEAT PROTECT CLIP -5dB -10dB LIMITER ON OFF 0 10 -15dB SIGNAL 0 10 PROFESSIONAL POWER AMPLIFIER V4000plus AMERICAN AUDIO® 4295 Charter Street Los Angeles Ca. 90058 Revised 02/02 User Instructions This symbol is intended to alert the user to the presence of non insulated "dangerous voltage" within the product's enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons. This symbol is intended to alert the user of the presence of important operating and maintenance (servicing) instructions in the literature accompanying the product. CAUTION: Risk of the electrical shock - DO NOT OPEN! [. . . ] To reduce the risk of shock or damage to your amplifier, be sure that the wire connected to one binding post does not come in contact with that of another. Spade Connector: (Diagram 6) Typical speaker output using bare wire. Insert bare wire into the binding post and tighten. When connecting your speakers to the amplifier using spade connector; Unscrew the red and black caps on the binding post, be sure not to completely remove or unscrew the red and black caps. Insert the spade connector in to the binding post and tighten the caps down on the spade connector. To reduce the risk of shock or damage to your amplifier, be sure that the wire connected to one binding post does not come in contact with that of another. When connecting your speakers to the amplifier using banana jacks; Be sure that the red and black caps on the binding post are tighten down completely. Insert the banana jacks into the caps of the binding post, be sure that the banana jack is inserted securely to avoid the risk of it popping out. Mono Bridge Connections: Mono bridge operation connections will follow the above descriptions however, when operating in mono bridge operation the speaker connections will run between the two positive (red) leads. Use channel two positive output terminal for the negative connection and the channel one positive output terminal for the positive connection. Diagram 11 Typical speaker output using spade connectors. Insert bare wire into the binding post and tighten. Stereo Connections Using the Neutrik Speakon output connectors: Recent regulatory requirements in Europe have outlawed the use of the dual banana plug and force amp users to terminate their speaker cables with spade lugs or bare wire ends. This is not advantageous to most users that want to reconfigure their systems or quickly change out an amp. The Neutrik Speakon® connector provides the most convenient solution to this problem, eliminating the need for spade lugs or bare wire end cables. Major speaker manufacturers have been using Speakon connectors on their products for years, so chances are you are ready to use the Speakon connection. With Speakon connectors, you can connect straight from the amplifier to the speaker. The Speakon connector used on this amplifier meets all known safety regulations. Once wired correctly, the connector cannot be plugged in backwards, causing the type of inverted polarity situations that have become common with banana hookups. This connection will provide a safe, secure and reliable method of connecting your speakers to your new amplifier. You can purchase the Speakon® NL4FC connectors from your local audio dealer. ©American Audio® - www. americandj. com - V4000plusTM Power Amplifier User Manual Page 8 OPERATING MODES: Always configure your amplifier operating mode before beginning operation. If you want to change it during performance. You must decrease the gain controls to their lowest levels to protect the speakers from any popping noise. Stereo Operation - Page 10/Figure 9 details an example of a typical stereo set-up. Connect your inputs into channels one and two of the amplifier. Connect your speakers to the outputs on the rear of the amplifier. Be sure that your front gain controls are turned down to their lowest level (full counter-clockwise). Use your front gain controls to regulate the output volume. [. . . ] You will also need high-quality two or four conductor speaker cable, a pair of needle-nosed pliers and a 1. 5-mm Allen key to assemble the Speakon connectors to your speaker wire. To assemble the Neutrik Speakon NL4FC connector, complete the following steps: 1. Strip back 3 /4-inch of the cable casing. Strip off 1 /4-inch from the end of each of the conductors down to bare wire, and insert the brass fittings ( Figure 10). [. . . ]