User manual AMERIPHONE AMPXB

[. . . ] In repairing your AM-PX/PXB, we may use new or reconditioned parts. If we elect to replace your AM-PX/PXB, we may replace it with a new or reconditioned product of the same or similar design. Repair or replacement will be warranted for either 90 days or the remaining time on the warranty period, whichever is longer. [. . . ] Its operation is subject to the following 2 conditions: ® PAGER SETTING (AM-PX) To set Pager feature: 1. DIP switch positions 5, 6, 7 and 8 determine the pager ID of each unit. Slide open the battery compartment and locate the DIP switch inside the AM-PX. Use a pen to move the DIP switches to set up the Pager feature as follows: ON · Leave all settings down OFF (off) for Pager ID #1 5678 · Push #5 switch up to ON position for Pager ID #2 · Push #6 switch up to ON position for Pager ID #3 · Push #7 switch up to ON position for Pager ID #4 · Push #8 switch up to ON position for Pager ID #5 ON OFF M08398 ALERTMASTER PERSONAL SIGNALER (AM-PX) and PERSONAL TACTILE SIGNALER (AM-PXB) ® Works with ALERTMASTER Product Series ® Your satisfaction with our products is very important to us. We would like to know what you like or dislike about our products and what we can do to make them even more beneficial to you. Please give us your comments by calling our Customer Service Department at the numbers given. We value your comments and appreciate your business. This device must accept any interference that may be received, including interference that may cause undesired operation. Patents Pending ©AMERIPHONE, AM-PX/PXB 5220-1041 1. This device may not cause harmful interference. 4/02 6 5678 ON OFF 5678 ON OFF OPERATING INSTRUCTIONS (For units without external antenna) 5678 ON OFF 5678 VOICE (800) 874-3005 TTY (800) 772-2889 FAX (714) 897-4703 ameriphonecs@plantronics. com www. ameriphone. com FEATURE IDENTIFICATION Battery charger jack Light indicators Page 1 2 3 4 5 OPERATIONS 1. It will alert you within an 80-foot radius of the Alertmaster base unit. Do not use the unit in the rain or in the shower. When the Alertmaster Notification System is activated by any function(s), the Signaler will come on for 24 seconds or until it is reset or turned off. ® CHANNEL SETTING The Alertmaster Notification System uses radio signals to communicate between the console unit and all its accessories. For the Personal Signaler to activate, they all have to be on the same "channel. " A "DIP Switch" is used for channel selection. ® IN CASE OF DIFFICULTY Symptom No power Cause and Remedy The Unit is turned off or battery needs recharging The DIP Switches may be incorrectly set. Or, it may be out of range. Reset Power switch ·Sound - Vibrates for one second, stops for one second, and repeats. This function is activated by the Baby Sound Monitor (AM-BX). ·Alarm - Vibrates for one second, stops for one second, and repeats. This function is also activated by the Audio Alarm Transmitter ( AM-AX). ·Sensor - Vibrates for one second, stops for one second, vibrates for one second, stops for two seconds, and repeats. [. . . ] If your system encounters interference and repeatedly activates by itself for no obvious reason, maybe it's being triggered by a system nearby. Change channel switch settings on all components. Unplug AC cord and locate DIP Switch on the underside of the Alertmaster base unit. It does not activate when the base unit is triggered Base Unit ON 1234 O F F Control buttons & raised letters (AM-PXB) only Use a pen or pencil to set DIP Switches to match exactly AM-PX AM-PXB AM PXB ON 12345678 ·Clock/Paging - Vibrates one second, stops for two seconds, and repeats. [. . . ]