User manual AMX AXB-TMCTMX+ TELEVISION MANAGER WITH CLOCK

[. . . ] instruction manual AXB-TMC/TMX+ Television Managers AXlink Bus Controllers AMX Limited Warranty and Disclaimer AMX Corporation warrants its products to be free of defects in material and workmanship under normal use for three (3) years from the date of purchase from AMX Corporation, with the following exceptions: · · · · · Electroluminescent and LCD Control Panels are warranted for three (3) years, except for the display and touch overlay components that are warranted for a period of one (1) year. Disk drive mechanisms, pan/tilt heads, power supplies, MX Series products, and KC Series products are warranted for a period of one (1) year. Unless otherwise specified, OEM and custom products are warranted for a period of one (1) year. Software is warranted for a period of ninety (90) days. [. . . ] 250 Response LED lights when channel is on. AXB-TMC Only: A push and release on this channel indicates that a scroll has completed. This occurs after all the trailing blanks (plus one) have scrolled off the display. ! I/O 1 is on (switch to GND) when channel is on. I/O 2 is on (switch to GND) when channel is on. I/O 3 is on (switch to GND) when channel is on. I/O 4 is on (switch to GND) when channel is on. Channel is on if CC-XPS External Frequency Scan Sensor detects horizontal scan frequency. Activating a channel (IR/Serial function) will deactivate the channel that is on. Contact closure inputs on I/O 1 through I/O 4 will also generate PUSHes and RELEASEs on channels 251 through 254, respectively. AXB-TMC/TMX+ Television Managers 19 Programming IR Functions (Synergy System Standard Order) The following table shows the standard IR function list. IR functions Function Description 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 PLAY > STOP [ ] PAUSE | | or STILL FFWD >> REWIND << SEARCH FWD >>| SEARCH REV |<< RECORD POWER or ON/OFF '0 ' or '10 ' '1 ' (channel digits) '2 ' '3 ' '4 ' '5 ' '6 ' '7 ' '8 ' '9 ' '+10 ' (for CD players typically) ENTER (used with numbers typically) Function Description 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 89 96 97 98 99 100 ! CHANNEL UP or + CHANNEL DOWN or VOLUME UP or + VOLUME DOWN or MUTE ON (power typically) OFF (power typically) TV/Video, TV/VCR, or TV/LDP (one button source selection) TV Video1, Line A, VCR1, VDP, or input + Video2, Line B, VCR2, or input Video3 RGB1 or Tape1 RGB2 or Tape2 CD TUNER PHONE AUX AM/FM PLAY < (play reverse) A/B CC TV/Video (Input 1) TV/Video (Input 2 SAP (Input 3) Input 4 Input 5 Synergy systems require that power (IR function 9) must be copied to functions 27 and 28, unless discrete power functions are already located there. In Synergy systems, specific Axcess program changes may be required to implement specific use of the Input 1 through Input 5 optional codes. ! 20 AXB-TMC/TMX+ Television Managers Programming System Send_Commands In the table below, system Send_Commands are stored in the Axcess Central Controller and direct the AXB-TMC/TMX+ to perform various operations. System Send_Commands CARON Turns the IR carrier on (default). Syntax: 'CARON' Example: SEND_COMMAND AXBTMX, 'CARON' Turns the IR carrier on (default). Syntax: 'CAROFF' Example: SEND_COMMAND AXBTMX, 'CAROFF' Turns the IR carrier off. Syntax: "'CH', <TV Channel>" Generates IR digit pulses to select a television channel number. Channels 100 and greater, the one-hundredth digit pulses as 127. If IR function 21 (enter) exists, it follows the IR digit pulses. CTON sets the pulse length for each digit and CTOF sets the time between each digit or any after-pulse. Example: SEND_COMMAND AXBTMX, "'CH', 25" Sets the television connected to channel 25 on the AXB-TMC/TMX+. Syntax: "'CTOF', <Time>" Sets the single IR pulses off time between channel digits and IR functions. This is the time between digits, or pulses, that are associated with an SP command. The <Time> value is returned in 10 second increments. [. . . ] AXB-TMC/TMX+ receives two digits but treats each as an individual channel command. Use the following command to shorten the off time in between digits: >CHANGE CTOF 3 71 The Master Controller should respond with the following: >Change CTOF to 3, First TM=71, Last TM=71 Where 3 is the off time in tenths of seconds (0. 3 seconds) and 71 is the device number. When using this command and other change commands, you cannot backspace while entering the message. You may need to type 'MESSAGES ON' before entering the above command to get the positive response. [. . . ]