User manual AMX AXP-CPI16 CUSTOM PANEL INTERFACE BOARD (16 BUTTONS)

[. . . ] The RMA number must be clearly marked on the outside of each box. After the 30-day period the RMA will be cancelled. Any shipments received not consistent with the RMA, or after the RMA is cancelled, will be refused. AMX is not responsible for products returned without a valid RMA number. [. . . ] 6 Preparing/connecting captive wires . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 Connecting the Two 20-pin Headers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 Switch Wiring Diagrams. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 Connecting the AXlink Wiring. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 Programming . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9 Testing the Unit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10 AXP-CPI16 System Worksheet . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11 AXP-CPI16 16-Channel Custom Panel Interface i Table of Contents ii AXP-CPI16 16-Channel Custom Panel Interface Product Information Product Information The AMX AXP-CPI16 16 Channel Custom Panel Interface Board (FIG. 1) simplifies the process of creating custom control panels for Axcess systems. Providing contact closure inputs and feedback outputs for up to 16 buttons, the miniature PC board contains a 20-pin header for ribbon cable installation or for direct mounting to a printed circuit board. AXlink Connector Pin 1 20-Pin Header P3 Connect this side to the ribbon cable Pin 1 Device DIP Switch AXlink Status LED -Pin Header P2 onnect this side to the ribbon cable FIG. 1 AXP-CPI16 components Connect this side to the PC board Specifications The following table lists product specifications for the AXP-CPI16. AXP-CPI16 Specifications Dimensions (HWD) Power Inputs Outputs 2. 75" x 1. 75" x 0. 062" (69. 90 mm x 44. 50 mm x 1. 557 mm) · Input voltage: 12 VDC (nominal) · Current draw: 25mA 16 closure inputs with a common ground (GND) 16 open-collector outputs, acting as switch to ground, up to 100 mA DC each for: · Board is not to supply more than 750 mA of +12V total. · Small incandescent lamps · LED indicators - with series resistor (1K for 12 VDC) · Relays - with DC coil AXlink Connector Headers A 4-pin (male) connector attached to a four-wire cable which sends control data from the Axcess CardFrame to the AXP-CPI16. Two 20-pin headers included for ribbon cables (up to 100 feet each) or for mounting directly to a PC board. AXP-CPI16 16-Channel Custom Panel Interface 1 Product Information AXP-CPI16 Specifications (Cont. ) AXlink Status LED Indicates AXlink communication status as follows: · One blink per second communication is functioning. · Two blinks per second devices specified in the master program do not match the specified devices found. · Three blinks per second indicate an AXlink communication error. · Full-on indicates there is no AXlink control or activity (but power is on), or the Axcess program is not loaded. Device DIP Switch Cables 8-position DIP switch sets AXlink device ID. Two 3-foot (91. 4 cm) ribbon cables each with a female 20-pin header. 2 AXP-CPI16 16-Channel Custom Panel Interface Product Information OFF OFF ON ON 12345 678 AXP-CPI16 16-Channel Custom Panel Interface 3 Product Information 4 AXP-CPI16 16-Channel Custom Panel Interface Installation Installation Mounting Dimensions B B A A A C C AXlink AXlink AXP GND PWR AXP AXM GND LH L J A P1 PWR AXM P1 12 12 P3 P3 Top View D D E E Top View (Component Side) (Component Side) 19 20 19 20 MM 2 1 F F P2 P2 20 20 19 19 J G G K K min min H FIG. 1 AXP-CPI16 mounting dimensions Mounting Dimensions Item Inch A B C D E F G H J 0. 10 1. 75 1. 55 2. 75 2. 55 0. 35 0. 23 0. 93 mm 2. 50 Item Description K P2 20-Pin Header . 025 inch (6 mm) square pins, . 1 inch (2. 4 mm) typical spacing 0. 125 Inch (3. 2 mm) mounting holes for #4-40 (3 mm) screws P3 20-Pin Header . 025 inch (6 mm) square pins, . 1 inch (2. 4 mm) typical spacing 44. 50 L 39. 40 M 69. 90 64. 80 8. 90 5. 80 23. 6 0. 438 11. 10 AXP-CPI16 16-Channel Custom Panel Interface 5 Installation Setting the AXlink Device Number The 8-position device DIP switch defines the AXP-CPI16 as an AXlink device. It can be one of 255 devices in the Axcess Control System. Set the device number with the total value of all ON (down) positions. As an example, the device DIP switch shown below defines device number 129 (1+128=129). Position 1 2 3 4 5 Value 6 7 8 OFF OFF ON ON 12345 678 1 2 4 8 16 32 64 128 AMX standard device numbers are assigned as follows: Cards are 1 through 25. Panels are 128 through 255. Preparing/connecting captive wires 1. Strip 0. 25 inch of wire insulation off all wires. [. . . ] This is because in this mode the output and input channels use the same number assignments. Inputs are sent by the AXP-CPI16 only as input changes. When set for STATUS-ON mode the output channels are assigned a different channel number than the input channels. This allows the programmer to monitor the status of an output channel. [. . . ]