User manual AMX FOLD-OUT-TVS TV SENSOR

[. . . ] This limitation of liability cannot be waived or amended by any person. This limitation of liability will be effective even if AMX Corporation or an authorized representative of AMX Corporation has been advised of the possibility of any such damages. This limitation of liability, however, will not apply to claims for personal injury. Some states do not allow a limitation of how long an implied warranty last. [. . . ] · fold EXCEPT AS EXPRESSLY SET FORTH IN THIS WARRANTY, AMX CORPORATION MAKES NO OTHER WARRANTIES, EXPRESSED OR IMPLIED, INCLUDING ANY IMPLIED WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE. AMX CORPORATION EXPRESSLY DISCLAIMS ALL WARRANTIES NOT STATED IN THIS LIMITED WARRANTY. ANY IMPLIED WARRANTIES THAT MAY BE IMPOSED BY LAW ARE LIMITED TO THE TERMS OF THIS LIMITED WARRANTY. EXCEPT AS EXPRESSLY SET FORTH IN THIS WARRANTY, AMX CORPORATION MAKES NO OTHER WARRANTIES, EXPRESSED OR IMPLIED, INCLUDING ANY IMPLIED WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE. AMX CORPORATION EXPRESSLY DISCLAIMS ALL WARRANTIES NOT STATED IN THIS LIMITED WARRANTY. ANY IMPLIED WARRANTIES THAT MAY BE IMPOSED BY LAW ARE LIMITED TO THE TERMS OF THIS LIMITED WARRANTY. 041-004-2605 6/02 ©2002 AMX Corporation. All Rights Reserved. 93-0691 Rev D 041-004-2605 6/02 ©2002 AMX Corporation. All Rights Reserved. All rights reserved. AMX, the AMX logo, the building icon, the home icon, and the light bulb icon are all trademarks of AMX Corporation. AMX reserves the right to alter specifications without notice at any time. *In Canada doing business as Panja Inc. All rights reserved. AMX, the AMX logo, the building icon, the home icon, and the light bulb icon are all trademarks of AMX Corporation. AMX reserves the right to alter specifications without notice at any time. *In Canada doing business as Panja Inc. 3000 research drive, richardson, TX 75082 USA 469. 624. 8000 · 800. 222. 0193 · fax 469. 624. 7153 technical support 800. 932. 6993 brussels · dallas · los angeles · mexico city · philadelphia · shanghai · singapore · tampa · toronto* · york 3000 research drive, richardson, TX 75082 USA 469. 624. 8000 · 800. 222. 0193 · fax 469. 624. 7153 technical support 800. 932. 6993 brussels · dallas · los angeles · mexico city · philadelphia · shanghai · singapore · tampa · toronto* · york cut TVS TV Sensor Control System Accessories TVS TV Sensor Control System Accessories cut cut cut fold fold fold 93-0691 Rev D cut cut TVS TV Sensor Overview The TVS TV Sensor detects whether a CRT (TV or monitor) is powered on by detecting the electromagnetic field generated by the CRT's electron gun mounted in the picture tube yoke. When the sensor detects this field, the TVS signal output (yellow wire) goes low. The TVS detects horizontal scan frequencies up to 90 kHz. Mount the TVS directly to the CRT with supplied VelcroTM strips, and connect to the INPUT/OUTPUT connectors on AMX devices. TVS features include: · · · Three-position switch sets the TVS detector sensitivity. Green LED signal indicator lights when a signal is detected. Compatible with any AMX device that accepts inputs (AXC-INP8, CPI-16, AXCENT3, etc. ). TVS TV Sensor Overview The TVS TV Sensor detects whether a CRT (TV or monitor) is powered on by detecting the electromagnetic field generated by the CRT's electron gun mounted in the picture tube yoke. When the sensor detects this field, the TVS signal output (yellow wire) goes low. The TVS detects horizontal scan frequencies up to 90 kHz. [. . . ] The green LED signal indicator must be visible during the installation process. If the green LED signal indicator does not light, move the TVS closer to the picture tube yoke, or set the SENSITIVITY switch to HIGH, or do both. To accommodate the electromagnetic field produced by large CRT's, you may have to move the TVS away from the picture tube yoke and/or reduce the sensitivity setting. When the green LED signal indicator lights, fasten the TVS to the CRT cabinet with the supplied VelcroTM strips. Installing the TVS To install the TVS: 1. Connect the TVS to the AMX device's INPUT/OUTPUT connector, following the wiring configuration chart (see Wiring the TVS). [. . . ]