User manual ANALOG DEVICES ADSP-2186

[. . . ] a FEATURES PERFORMANCE 25 ns Instruction Cycle Time 40 MIPS Sustained Performance Single-Cycle Instruction Execution Single-Cycle Context Switch 3-Bus Architecture Allows Dual Operand Fetches in Every Instruction Cycle Multifunction Instructions Power-Down Mode Featuring Low CMOS Standby Power Dissipation with 100 Cycle Recovery from Power-Down Condition Low Power Dissipation in Idle Mode INTEGRATION ADSP-2100 Family Code Compatible, with Instruction Set Extensions 40K Bytes of On-Chip RAM, Configured as 8K Words On-Chip Program Memory RAM and 8K Words On-Chip Data Memory RAM Dual Purpose Program Memory for Both Instruction and Data Storage Independent ALU, Multiplier/Accumulator and Barrel Shifter Computational Units Two Independent Data Address Generators Powerful Program Sequencer Provides Zero Overhead Looping Conditional Instruction Execution Programmable 16-Bit Interval Timer with Prescaler 100-Lead LQFP and 144-Ball Mini-BGA SYSTEM INTERFACE 16-Bit Internal DMA Port for High Speed Access to On-Chip Memory (Mode Selectable) 4 MByte Byte Memory Interface for Storage of Data Tables and Program Overlays 8-Bit DMA to Byte Memory for Transparent Program and Data Memory Transfers (Mode Selectable) I/O Memory Interface with 2048 Locations Supports Parallel Peripherals (Mode Selectable) Programmable Memory Strobe and Separate I/O Memory Space Permits "Glueless" System Design (Mode Selectable) Programmable Wait State Generation Two Double-Buffered Serial Ports with Companding Hardware and Automatic Data Buffering DATA ADDRESS GENERATORS DAG 1 DAG 2 PROGRAM SEQUENCER DSP Microcomputer ADSP-2186 FUNCTIONAL BLOCK DIAGRAM POWER-DOWN CONTROL MEMORY 8K 24 PROGRAM MEMORY 8K 16 DATA MEMORY PROGRAMMABLE I/O AND FLAGS FULL MEMORY MODE EXTERNAL ADDRESS BUS EXTERNAL DATA BUS BYTE DMA CONTROLLER PROGRAM MEMORY ADDRESS DATA MEMORY ADDRESS PROGRAM MEMORY DATA OR DATA MEMORY DATA EXTERNAL DATA BUS ARITHMETIC UNITS ALU MAC SHIFTER SERIAL PORTS SPORT 0 SPORT 1 TIMER INTERNAL DMA PORT HOST MODE ADSP-2100 BASE ARCHITECTURE Automatic Booting of On-Chip Program Memory from Byte-Wide External Memory, e. g. , EPROM, or Through Internal DMA Port Six External Interrupts 13 Programmable Flag Pins Provide Flexible System Signaling UART Emulation through Software SPORT Reconfiguration ICE-PortTM Emulator Interface Supports Debugging in Final Systems GENERAL DESCRIPTION The ADSP-2186 is a single-chip microcomputer optimized for digital signal processing (DSP) and other high speed numeric processing applications. The ADSP-2186 combines the ADSP-2100 family base architecture (three computational units, data address generators and a program sequencer) with two serial ports, a 16-bit internal DMA port, a byte DMA port, a programmable timer, Flag I/O, extensive interrupt capabilities and on-chip program and data memory. The ADSP-2186 integrates 40K bytes of on-chip memory configured as 8K words (24-bit) of program RAM and 8K words (16-bit) of data RAM. Power-down circuitry is also provided to meet the low power needs of battery operated portable equipment. [. . . ] B ­9­ ADSP-2186 Byte Memory DMA (BDMA, Full Memory Mode) Internal Memory DMA Port (IDMA Port; Host Memory Mode) The Byte memory DMA controller allows loading and storing of program instructions and data using the byte memory space. The BDMA circuit is able to access the byte memory space while the processor is operating normally and steals only one DSP cycle per 8-, 16- or 24-bit word transferred. The BDMA circuit supports four different data formats that are selected by the BTYPE register field. The appropriate number of 8-bit accesses is done from the byte memory space to build the word size selected. Table V shows the data formats supported by the BDMA circuit. Table V. BDMA Data Formats The IDMA Port provides an efficient means of communication between a host system and the ADSP-2186. The port is used to access the on-chip program memory and data memory of the DSP with only one DSP cycle per word overhead. The IDMA port cannot, however, be used to write to the DSP's memorymapped control registers. The IDMA port has a 16-bit multiplexed address and data bus and supports 24-bit program memory. The IDMA port is completely asynchronous and can be written to while the ADSP-2186 is operating at full speed. The DSP memory address is latched and then automatically incremented after each IDMA transaction. An external device can therefore access a block of sequentially addressed memory by specifying only the starting address of the block. This increases throughput as the address does not have to be sent for each memory access. The first is the IDMA Address Latch cycle. When the acknowledge is asserted, a 14-bit address and 1-bit destination type can be driven onto the bus by an external device. The address specifies an on-chip memory location, the destination type specifies whether it is a DM or PM access. The falling edge of the address latch signal latches this value into the IDMAA register. Once the address is stored, data can then either be read from or written to the ADSP-2186's on-chip memory. Asserting the select line (IS) and the appropriate read or write line (IRD and IWR respectively) signals the ADSP-2186 that a particular transaction is required. In either case, there is a one-processorcycle delay for synchronization. The memory access consumes one additional processor cycle. Once an access has occurred, the latched address is automatically incremented and another access can occur. [. . . ] TEST CONDITIONS CAUSE THIS VOLTAGE LEVEL TO BE APPROXIMATELY 1. 5V. Figure 27. Output Enable/Disable IOL Figure 25. Load Capacitance, CL (at Maximum Ambient Operating Temperature) TEST CONDITIONS Output Disable Time TO OUTPUT PIN 50pF +1. 5V Output pins are considered to be disabled when they have stopped driving and started a transition from the measured output high or low voltage to a high impedance state. The output disable time (tDIS) is the difference of tMEASURED and tDECAY, as shown in the Output Enable/Disable diagram. [. . . ]