User manual AOC LM540

[. . . ] LM540 LM540 15 inch TFT LCD Monitor User's Manual by Envision Peripherals, Inc. www. AOCdisplay. com Before operating your monitor, please read this manual thoroughly. LM540 1 17NOV04 For Your Safety FCC Statement This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy, and if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. [. . . ] · Periodically clean your monitor with a soft cloth. Stubborn stains may be removed with a cloth lightly dampened with a mild detergent solution. Never use strong solvents such as thinners, benzene, or abrasive cleaners, since these will damage the cabinet. Always unplug the monitor before cleaning it. Using the Right Power Cord The supplied power cord is a NEMA 5-15 style plug. It is UL-listed and CSA labeled for 125 volts AC. If the monitor will be connected to your computer's power outlet, use a minimum No. 18 AWG, type SJT or SVT three conductors cord with one end terminating with a male grounded plug, rated 10A, 250V, CEE-22. The other end must terminate with a molded-on type connector body, rated 10A, 250V, having standard CEE-22 female configuration. 4 17NOV04 LM540 Before You Operate the Monitor Installing & Removing the Base LM540 General Features: · 38. 1cm(15") TFT Color LCD Monitor · Crisp, Clear Display for Windows · Supports Resolutions up to 1024 X 768 pixels @75Hz, (1024 x 768 @ 60Hz Recommended) · EPA ENERGY STAR® · Ergonomic Design · Space Saving, Compact Case Design LM540 Package Contents The box that your monitor was shipped in should have included the following items: 1. Windows 95/98/2000/ME/XP INF Driver Disk 4. Booklet (Containing Warranty & Safety Information) 5 17NOV04 Before You Operate the Monitor Connecting the Wires Using the Power Cord Supplied LM540 1. Connect the built-in video cable into the 15-pin connector on the back of your computer and tighten the two screws. Connect the power cord into your LCD monitor's Power Adapter. Connect the Power Adapter to your monitor. Plug the other end of the power cord into a grounded AC outlet or UL-approved power strip. Caution: Make sure the power cord is the correct type that is required in your area. This LCD monitor has a universal power supply that allows operation in either 100/120V AC or 220/240V AC voltage areas (no user adjustment is required). If the AC outlet is not grounded (with three holes), install the proper grounding adapter (not supplied). LM540 6 17NOV04 Before You Operate the Monitor Adjusting the Viewing Angle LM540 For optimal viewing, adjust the monitor's angle to your own preference. · Hold the stand firmly when you change the monitor's angle. · You can adjust the monitor's angle from -5° to 25°. · Do not touch the LCD screen when you change the angle. · Be careful to avoid pinching your hand in the swivel base. LM540 7 17NOV04 Before You Operate the Monitor LM540 Preparing To Install An Optional Wall Mounting Arm (Not Supplied) This monitor can be attached to a wall mounting arm you can purchase separately. Disconnect power before performing this procedure. Pull the screw covers off the back of the monitor. [. . . ] The host can request EDID information over the DDC2B. LM540 How to Install INF & ICM File 1. Insert the Windows 95/98/2000/ME/XP INF Driver Disk into your floppy drive. Follow the Add New Hardware Wizard instructions on the screen. If the wizard asks for the location of the driver file, select drive A and press Next. LM540 12 17NOV04 Technical Support (FAQ) Problem Power LED is not ON LM540 Possible Solution · Make sure the power button is ON. [. . . ]