User manual AOC LM729

[. . . ] LM729 LM729 17" LCD Monitor User's Manual By Envision Peripherals, Inc. www. aocmonitor. com . LM729 TABLE OF CONTENTS Table of Contents For Your Safety Precautions General Notes Before You Operate The Monitor Installation Instructions Operating Instructions Technical Support (FAQ) Appendix 1 2 3 4-5 6 7-13 14-19 20-21 22-25 1 LM729 FOR YOUR SAFETY Before operating the monitor, please read this manual thoroughly. This manual should be retained for future reference. FCC Class B Radio Frequency Interference Statement WARNING: (FOR FCC CERTIFIED MODELS) NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. [. . . ] The DDC 2B is a bidirectional data channel based on the I2C protocol. The host can request EDID information over the DDC 2B channel. · This monitor will appear to be non-functional if there is not video input signal. In order for this monitor to operate properly, there must be a video input signal. 5 LM729 BEFORE YOU OPERATE THE MONITOR FEATURES · · · · · · · 17" (43. 2cm) TFT Color LCD Monitor Crisp & Clear Display for Windows Recommended Resolutions: 1280 X 1024 @ 60Hz ® EPA ENERGY STAR 2W + 2W Stereo Speakers Ergonomic Design with Height, Pivot, Tilt & Swivel Adjustable Stand Space Saving, Compact Case Design CHECKING THE CONTENTS OF THE PACKAGE The product package should include the following items: Monitor Base Quick Start Guide (QSG) CD (Manual & Drivers) 15-pin D-Sub Cable Power Cord PC Stereo Cable Warranty Booklet 6 LM729 INSTALLATION INSTRUCTIONS INSTALLING & REMOVING THE BASE Install Figure 1 - Installing the Base. Line up the front of the monitor with the front of the base and press firmly. Remove Pin Remove Base Figure 2 - Installing the Base. Never remove the base while the height adjustment lock pin is installed. Set the monitor standing on a flat firm surface. Set the monitor face down on a padded flat surface. Press the four clips inward while pushing the bottom base out. 7 LM729 INSTALLATION INSTRUCTIONS (Cont) POWERCORD Power Source: 1. Make sure that the power cord is the correct type required in your area. This LCD monitor has an internal Universal Power Supply that allows operation in either 100/120V AC or 220/240V AC voltage area (No user adjustment is required. ) 3. Connect the AC-power cord into your LCD monitor's AC-power-input. The AC-power cord may be connected to either a wall power outlet or the power outlet socket on your PC, depending on the type of power cord supplied with your LCD monitor. A certified power supply cord has to be used with this equipment. The relevant national installation and/or equipment regulations shall be considered. A certified power supply cord not lighter than ordinary polyvinyl chloride flexible cord according to IEC 60227 (designation H05VV-F 3G 2 2 0. 75mm or H05VVH2-F2 3G 0. 75mm ) shall be used. As an alternate, a flexible cord of synthetic rubber according to IEC 60245 (designation H05RR2 F 3G 0. 75mm ) shall be used. The accessory power cord for the Northern American region is the wall plug with NEMA 5-15 style and is UL listed and CSA labeled. The voltage rating for the power cord shall be 125 volts AC. Supplied with units intended for connection to power outlet of personal computer: Please use a cord set consisting of a minimum No. 18 AWG, type SJT or SVT three conductors flexible cord. One end terminates with a grounding type attachment plug, rated 10A, 250V, CEE-22 male configuration. The other end terminates with a molded-on type connector body, rated 10A, 250V, having standard CEE-22 female configuration. [. . . ] The Language will be set to English. Deutsch N/A Français N/A Español N/A Italiano N/A N/A 18 LM729 OPERATING INSTRUCTIONS (cont) Main Menu Item Informati on Main Menu Icon Sub Menu Item Informati on Sub Menu Icon N/A Reset Value N/A Description Show the resolution, H/V frequency and input port of current iput timing. Clear each old status of Autoconfiguration and set the color temperature to Cool. Do not execute reset, return to main menu. Exit OSD Reset Yes N/A N/A No Exit N/A N/A N/A N/A N/A 19 LM729 TECHNICAL SUPPORT (FAQ) Problem & Question Power LED is not on Possible Solution *Check if the Power Switch is in the ON position *Power Cord should be connected *Check if the PC system is Plug & Play compatible *Check if the Video Card is Plug & Play compatible *Check if the D-15 plug pin of Video Cable is bent *Adjust the Contrast and Brightness Controls. [. . . ]