User manual AOPEN AON325

[. . . ] Table of Contents FULL PACKAGE CONTENT. . . 11 Full Package Content The adapter package should contain the following items: · One PCI 10/100 Ethernet adapter · User' s guide · Driver diskette Please inform your dealer immediately should there be any incorrect, missing or damaged parts. Introduction The 10/100 Based-Tx Fast Ethernet Adapter card is a 32-bit 10/100Mbps Ethernet network interface card for PCI local bus-compliant PCs. It supports the PCI bus mastering architecture which allows data to be transferred very fast with low CPU utilization and auto-negotiation feature which makes it possible to combine one common type of Ethernet cabling-an RJ-45 connector for twistedpair cabling that can be used for both 10Mbps and 100Mbps connection. [. . . ] · Drivers for all leading Network Operating Systems. · Two LED indicators: Link, Activity. · LINK Indicator A steady green LED indicates good linkage between the 32-bit PCI bus 10/100Mbps Fast Ethernet Adapter and its supporting hub. · ACTIVITY Indicator A flashing green LED indicates that the adapter is sending or receiving data. Software Driver Support l l Diagnostic Program ODI Novell Client Dos, Novell Client 32 for Dos, Netware Sever 3. x, 4. x, 5. 0 l NDIS 2. x, 3. x, 4. x, 5. 0 Windows 2000, Windows 98, Windows 95 OSR2, Windows 95, Windows NT, WindowsWPW3. 11, MS LAN, LANtastic, OS/2 LAN server and client l l l Packet Driver : FTP PC/TCP UNIX Driver : SCO UNIX Linux Installation Installation of a 10/100Mbps PCI bus Fast Ethernet Card requires Hardware installation first, then BIOS and Software installation. Hardware Installation 1. Turn OFF the computer, unplug its power cord and open the computer case. Insert the contact edge of the 10/100Mbps PCI bus Fast Ethernet Card into the connector of any available PCI Bus Master expansion slot. Press the card firmly into the connector and ascertain that the card contacts are fully seated in the connector. Install the bracket screw, which secures the card to the cincture chassis. Replace the computer' s case and connect the network cable to newly installed network card. Reconnect the computer' s power cord and plug it into the power outlet. 3. 4. Driver Installation Before you connect the 10/100Mbps PCI bus Card to the network, you have to install the network driver first. The driver for each networking operating system is under a separate directory. A HELP. EXE file under root directory lists the information and detailed installation procedure of all the available drivers. Boot ROM Installation The optional Boot ROM device allows you to connect a diskless workstation to the network. Perform the following steps to install your Boot ROM device: Note: Install the optional remote boot ROM before installing the card. Note: Before handling the remote boot ROM chip, discharge any static electricity on your body by touching a grounding surface such as the chassis of the PC. Align the notch and pins of the ROM chip with notch and pinholes on the socket. [. . . ] Install the questioned adapter in another PCI computer and run the tests again. Remove all other PCI adapters from the computer and run the tests again. If the verification/diagnostic run is not normal, then there is probably an interrupt number conflict which will have to be resolved manually by a CMOS Setup utility run after you have reinstalled all of the expansion cards. Specifications IEEE 802. 3 10BASE-T IEEE802. 3u 100BASE-TX PCI Local Bus specification Rev. 2. 1 Host interface: PCI 2. 1 Bus (Bus Master) Data Bus Width: 32-bit PCI bus mastering Jumperless Hardware Auto-negotiation functionality LED indicators: Link, Activity Media Interface: RJ-45 Emissions: FCC Class B CE Certification, Class B VCCI-II Dimensions: 120mm x 58mm Storage Temperature: -25°C ~ 70°C Operating Temp. : 0°C ~ 50°C Storage Humidity: 10%~ 90% noncondensing Operating Humidity: 10%~ 70% non-condensing Power Consumption: 1. 1 Watts (maximum) Standards: [. . . ]