User manual AOPEN CRW9420

[. . . ] The Compact Disc Recorder/ Rewriter Driver's configuration, Function Block Diagram and Connector are shown below; Fig. 1 Compact Disc Rewritable Drive configuration 2 2. Connector The Connectors are located as shown below. The function of each parts are also described below. Fig. [. . . ] 2. 9 Audio Output Connector Used to connect to the sound card. (Analog signal. ) 2. 10 Digital Audio Output (Not used) Used to connect to the sound card. (Digital signal. ) It is not used with this drive. 2. 11 Device Configuration Jumper Used when selecting the Device Configuration of E-IDE. Don't use jumpers to change anything besides the Device Configuration, but keep the drive as initially set ("Master" position). Configuration changes become valid after power is turned off, then on again. Caution: Installing jumper pins besides the ones for Device Configuration settings may be the cause of damage or abnormal drive operation. Fig. 4 Device Configuration Jumper The Device Configuration Jumper will be set to Master as factory setting. Functionality 1. 1 Recording Data should be recorded on the optical disc in response to host computer command. Drive receives necessary information such as logical block address, number of block and data to be recorded from the host computer. Recording to pre-recorded area can not be executed. Overwriting to pre-recorded area can not be executed. (CD-RW disc) 1. 2 Reading Data on optical disc should be read in response to the host computer command. Audio playing (CD-DA) can be executed when receiving the Audio playing command from the host computer. Load the disc by pushing the eject button or by lightly pushing in the disc tray. Eject Operator can eject the Disc Tray (Disc) by pushing this button. 1. 4 Spindle Motor Start/Stop This controller of the drive senses the disc to be set on the turn-table connected with the spindle motor and then starts to rotate the spindle motor, in response to the host computer command. 6 1. 5 Seek Motor The controller of the drive starts to move the optical pick up carriage, in response to the host computer command. 1. 6 Eject Button Operator can eject the Disc Tray (Disc) by pushing this button. 1. 7 Busy indicator When the disc tray or disc is being accessed, the light shines or flashes orange. Even when a disc is loaded or a disc is not being accessed, the light go out. When a illegal disc is loaded or some hardware trouble occurs, the indicator blinks. 2. Basic Specification Type: Tray Type Supported Function (Write/Read/Play) Write CD-DA CD-ROM CD-Extra CD-ROM XA Photo CD * 2 CD-I * 2 CD-ROM + CD-DA Video-CD P P P P P P P P Read P P P P P P P P P P P P Play*1 P * Play means Audio play back. [. . . ] Safety Standards Application Standard: Ratio Interference: UL, cUL, CE, CDRH Vcci-II, FCC-Class B, EN55022-Class B 8. Storage Conditions 8. 1 Storage Conditions Temperature: Humidity: Temperature Gradient: Humidity Gradient: Vibration Shock: Drop: Altitude: Illuminance: Preservation Term: -30 ~ 65 C (Max. ) 5 ~ 95% 20%/Hour (Max. ) 10%/Hour (Max. ) 1. 0 x 9. 8m/s2 (1. 0G) or less (5300Hz) 40 x 9. 8m/s2 (40. 0G) or less (11msec. Halfsine) 60. 0 cm JIS Z0202 -305 ~ 15, 240m 3, 000 Lux or less year or less 8. 2 Transportation Condition Container: Means of Transportation: Stacking Layers: Attached Articles: Cardboard Packing Case Mixed loading possible 6 or less Caution 12 9. Emergency Eject This unit is equipped with a mechanism for manually ejecting the Disc Tray in an emergency, such as when the loading mechanism has failed or power has been lost. [. . . ]