User manual AOPEN DX37PLUSUG

[. . . ] Installing CPU & System Fan Plug in the CPU fan cable to the 3-pin CPU1 FAN and CPU2 FAN connector. If you have chassis fan, you can also plug it on System FAN (FAN2) or AUX FAN (FAN3) connector. FAN3 Connector GND +12V Sensor CPU1 Fan Connector GND +12V SENSOR PART NO: 90. 53G30. 006 DOC. NO: DX37PU-EG-E0112B GND +12V Sensor FAN1 Connector Note: Some CPU fans do not have sensor pin so they cannot support fan monitoring. 3. [. . . ] Make sure you plug in the right direction. +12V 5VSB COM 2 9. Connecting Front Panel Cable Attaching such as power LED, speaker, reset switch, power switch connector, etc. . . . The green cap on pin 19 & 20 is to disable Chassis Intrusion Switch, you may just take it off to able this function. 21 22 Chassis Intrusion Switch Reset Switch +5V +5V -5V COM COM COM PS-ON ATX Power Switch Pin 1 Power LED HDD LED COM +5V COM COM +3. 3V +3. 3V COM -12V +3. 3V 12 21 22 INT S/W RST S/W +5V GND PWR LED GND GND +5V HDD LED HDD LED +5V GND 12 GND +3. 3 V +5VSB 10. Connecting 68-pin Ultra 160 SCSI Cable (DX37 Plus-U only) The DX37Plus-U provides two 68-pin Ultra Wide/Ultra 2/3 SCSI connectors for 16-bit or 16-bit differential SCSI devices. CD-IN (Black) 12. Connecting CD / AUX Connector The AUX-IN connector is used to connect MPEG Audio cable from MPEG card to onboard sound. The CD-IN connector is used to connect CD Audio cable from CDROM or DVD drive to onboard sound. AUX-IN (Green) SW1(3) SW1(4) On On Disable SCSI Ch A Terminator Disable SCSI Ch B Terminator Connector AUX-IN CD-IN Pin1 Left Left Pin2 GND GND Pin3 GND GND Pin4 Right Right A Terminator B Terminator 11. Connecting SCSI Card LED Connector (DX37 Plus-U only) The 4-pin SCSI LED connector can be connected to a PCI SCSI control card activity LED connector. Read or write activity by devices connected to the SCSI card will transfer a signal to Front Panel and thus making the LED lighting up. 13. Redundant SPS Monitoring Connector This motherboard implements Redundant SPS monitoring connector to provide hardware monitoring signals. It is feasible to install an additional 337-watt power supply module (optional with AOpen Server Housing) in a hot swappable configuration. If any SPS failed, a signal will be sent to a hardware monitoring device. + + SCSI Card LED Connector +12V Present 3 GND 5VSB Present 2 Fan 2 Fail PS 2 Fail 14 13 Fan 3 Fail PS 3 Fail PS ON Present1 I2C CLK Fan 1 Fail PS1 Fail 2 1 14. Support 10/100 Mbps LAN onboard The South Bridge V8233 of VIA Apollo Pro266T chipset includes a fast Ethernet controller on chip. On the strength of Intel 82550 PHY on board, which is a highly-integrated Platform LAN Connect device, it provides 10/100M bps Ethernet for office and home use, the Ethernet RJ45 connector is located on the back panel. The green LED indicates the link mode, it lights when linking to network and blinking when transferring data. The orange LED indicates the transfer mode, and it lights when data is transferring in 100Mbps mode. To enable or disable this function, you may simply adjust it through BIOS. Wake On LAN To use Wake On LAN function, you must have a network card with chipset that supports this feature, and connect a cable from LAN card to motherboard WOL connector. The system identification information (probably IP address) is stored on network card and because there is a lot of traffic on the Ethernet, you need to install a network management software, such as ADM, for the checking of how to wake up the system. Note that, at least 600mA ATX standby current is required to support the LAN card for this function. Orange/Speed +5VSB GND LID 15. Power-On and Load BIOS Setup After you finish the setting of jumpers and connect correct cables. Power on and enter the BIOS Setup, press <Del> during POST (Power On Self Test). [. . . ] http://www. aopen. com/tech/download/manual/default. htm 2 3 Test Report: We recommend to choose board/card/device from the compatibility test reports for assembling your PC. http://www. aopen. com/tech/report/default. htm FAQ: The latest FAQ (Frequently Asked Questions) may contain a solution to your problem. http://www. aopen. com/tech/faq/default. htm 4 5 Download Software: Check out this table to get the latest updated BIOS/utility and drivers. http://www. aopen. com/tech/download/default. htm China () Tel: 86-21-6225-8622 Fax: 86-21-6225-7926 Germany AOpen Computer GmbH. [. . . ]