User manual AOPEN H800-SELLING

[. . . ] AOpen reserves the right to make revisions to this publication without obligation to notify any person or entity of any such changes. AOpen® is a registered trademark of AOpen Inc. Other trademarks or brand names mentioned herein are trademarks or registered trademarks of their respective owners. Table of Contents 1. 2. Introduction. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] All fans are hot swappable, allowing users to replace malfunctioning fans without turning off the system. g g If you want to install one more 8cm fan, you must take out the fan cover first. Put the fan into HDD cage, screw it on, and then arrange the fan cable. User's Guide 2-8 Parts Description 2. 5. Security Device The H800-SELLING-SELLING has one mechanical key lock on the front panel cover and one electrical chassis intrusion alarm to prevent unauthorized access to components inside the chassis. The chassis intrusion alarm is an electrical detecting device that came with the motherboard. It will alarm whenever the front panel or side panels are opened. The overall security system protects this server chassis perfectly. Key lock for system security H800-SELLING-SELLING Server Chassis Parts Description 2-9 2. 6. Power Supplies nd The H800-SELLING-SELLING supports standard ATX 12V and redundant 337W (with or without 2 power) power supplies. 2. 6. 1 Standard ATX 12V power supply Before Assembly standard ATX 12V power supply, it must assemble power bracket with power than can install to chassis. Standard ATX 12V 350/400W Power Bracket b Standard ATX 2. 6. 1. 1. 350W ATX 12V Power Supply Specification GENERAL REQUIREMENTS This specification describes a 350 watts power supply. With + 5V stand-by and remote ON/OFF control for ATX system. User's Guide 2-10 INPUT REQUIREMENTS Parts Description The power supply shall operate from 95 to 132 Vrms or 180 to 264 Vrms. The power supply shall operate from an AC mains frequency of 47 through 63 Hz. The Ac mains single-cycle peak inrush current shall be limited to 80 amps cold, 100 amps warm measured at 132 Vrms, 60 Hz and coinciding with the AC main voltage peak. The AC mains steady-state RMS input current shall be: 10 amps maximum / 115 Vrms, 60 Hz. 5. 0 amps maximum / 230 Vrms, 50 Hz. OUTPUT REQUIREMENTS OUTPUT VOLTAGE AND CURRENT MINIMUM LOAD +3. 3V +5V +12V -12V -5V +5Vsb 0. 2A 2. 0A 0. 2A 0. 0A 0. 0A 0. 0A NORMAL LOAD 14. 0A 12. 7A 4. 5A 0. 4A 0. 15A 1. 0A MAXIMUM LOAD 18/28A 32/25. 5A 15. 0A 0. 8A 0. 3A 2. 0A LOAD REG. ¡Ó 5% ¡Ó 5% ¡Ó 5% ¡Ó 10% ¡Ó 10% ¡Ó 5% RIPPLE & NOISE 50mV P-P 50mV P-P 120mV P-P 120mV P-P 100mV P-P 50mV P-P (1). +3. 3V &+5V total output not exceed 220W. There are two configurations described as below : (1) One single power supply operation, It is configured as one cage unit ( Delta module name RPS-600A) compatible with one power supply unit ( Delta model name DPS-300AB-1) for single power supply operation (2) Dual power supplies redundant operation, It's configured with one cage unit ( RPS-600A) compatible with two units of power supply (DPS-300AB-1) for dual power supply current sharing operation. Under dual power supply redundant operation, the power supply's output current are controlled electronically so that both power supplies share the loads. Electrical Characteristics : (1) (2) (3) (4) Input voltage range: 90 Vac ~ 264 Vac, auto-range, single phase Input frequency range: 47 Hz to 63 Hz. @ 230 Vac, full load Inrush current of this module shall not exceed 60 amperes peak at 100 vrms input voltage, the inrush current measured at cold start. At low line 110/220 VAC (60Hz) full load. (6) Power Factor Correction : the power module (RPS-600A compatible with H800-SELLING-SELLING Server Chassis Parts Description 2-15 DPS-300AB-1) shall meet the IEC-1000-3-2 Standard. (7) Electrical performance should compatible with RPS-600A. Static Output Characteristics: OUTPUT VOLTAGE +3. 3V +5V +12V -5V -12V 5V AUX LOAD RANGE MIN. 0. 5A 0. 5A 0. 2A 0A 0A 0A LOAD RANGE REGULATION MAX. 14A 33A 10A 0. 3A 0. 5A 0. 9A +4% ~ -4% +5% ~ -5% +5% ~ -5% +10% ~ -10% +10% ~ -9% +5% ~ -5% RIPPLE P-P MAX. 50mV 50mV 120mV 100mV 200mV 100mV RIPPLE +NOISE 80mV 100mV 200mV 200mV 200mV 100mV Note : 1. +5V and 3. 3V total combination output power should not over 205w. The cross regulation is defined in the matrix below. Conducted EMI : -FCC docket 20780. [. . . ] Connect cables to the correct position step by step according to the motherboard manual. Connect other devices (keyboard, mouse, monitor) and try to power on to check the system configuration. Slide the side panel and fasten it with thumbscrew before putting down the front panel and lock. b H800-SELLING-SELLING Server Chassis Optional Parts Lists 4-1 3. 7. Rack Mount Placement Release all handle, wheels, and foot stands first. Screw off the top cover 6pcs screw then change the top cover to rack mount type and screw on. [. . . ]