User manual AOPEN I945GTM-VHL0602A1

[. . . ] Chapter 1 Table of Contents Table of Contents 1. 1 Disposal Instruction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 1. 2 A Thank-you Note Before You Get Start. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 1. 3 Features of This Manual . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 1. 4 Safety Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 Chapter 1 Table of Contents. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 Chapter 2 Introduction to This Motherboard . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 2. 1 How does your motherboard look like?. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 2. 2 Specification . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9 2. 3 Block Diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10 Chapter 3 Hardware Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] You can press <Esc> key to quit Phoenix-AwardTM BIOS setup program. The following table provides details about how to use keyboard in the Phoenix-AwardBIOS setup program. Key Page Up or + Page Down or Enter Esc Up Arrow Down Arrow Left Arrow Right Arrow F7 F10 Description Change setting to next value or increase the value. Change setting to previous value or decrease value. In main menu: Quit without saving any changes. In sub menu: Exit current menu to main menu. Move the light bar to left side of menu. Move the light bar to right side of menu. Save changed settings and exit setup program. 5. 3 How To Enter BIOS Setup After finishing the jumper settings and connecting cables, you can power on and enter the BIOS Setup. Press <Del> during POST (Power-On Self Test) and choose "Load Setup Defaults" for recommended optimal performance. Del 44 Standard CMOS Features The "Standard CMOS Setup" sets the basic system parameters such as the date, time, and the hard disk type. Use the arrow keys to highlight an item and <PgUp> or <PgDn> to select the value for each item. Standard CMOS Features > Date To set the date, highlight the Date parameter. Press <PgUp> or <PgDn> to set the current date. The date format is month, date, and year. Standard CMOS features > Time To set the time, highlight the Time parameter. Press <PgUp> or <PgDn> to set the current time in hour, minute, and second format. The time is based on the 24 hour military clock. Standard CMOS features > IDE Channel 0 Master Standard CMOS features > IDE Channel 0 Slave Standard CMOS features > IDE Channel 2 Master Standard CMOS features > IDE Channel 2 Slave This item lets you select the IDE hard disk parameters that your system supports. These parameters are Size, Number of Cylinder, Number of Head, Start Cylinder for Pre-compensation, Cylinder number of Head Landing Zone and Number of Sector per Track. The default setting is Auto, which enables BIOS to automatically detect the parameters of installed HDD (Hard Disk Drive) at POST (Power-On Self Test). If you prefer to enter HDD parameters manually, select Manual. 45 IDE HDD Auto-Detection: Press "Enter" to auto-detect parameters of HDD IDE Channel 0 Master (Slave): Define the parameters of IDE devices in Channel 0 (Master or Slave). Available options: None: if there is no device, please select "None" for speeding boot up. Auto: enable BIOS to auto-detect parameters of IDE device. (Default) Manual: allow users to define parameter of IDE device. [. . . ] If want to support both output devices, please change "Dual Monitor Mode" to "Extended Mode" (3) Because both of YPbPr and D connector are from the same signal, select either one to output will get the better quality. (4) If you pull out the primary device under Dual Monitor Mode and reboot, the secondary device's screen will be dark. You can use hotkey to set the primary device. Hot Key List Ctrl + Alt + F1 Ctrl + Alt + F2 Ctrl + Alt + F4 Output Device as Primary D-SUB TV (set as primary) DVI (5) When plug Geforce FX5200 PCI VGA card, the system will be crashed. [. . . ]