User manual AOPEN SX34G

[. . . ] Installing CPU & System Fan There are four system FAN connectors provided by Fortress1100 system. Each of them is a 3-pin connector, which brings the failure report, 12V power and ground. The system FAN is designed with redundancy to prevent thermal disaster caused by FAN failure. FAN1 Connector GND +12V SENSOR GND +12V SENSOR IDE ATA Cable x 2 Heat-sink x 1 Screw Package (10 HDD Screws) Bonus Pack CD x 1 This Easy Installation Guide x 1 One set rubber feet (4) FAN4 Connector GND +12V SENSOR FAN3 Connector Fan2 Connector Note: Some CPU fans do not have sensor pin so they cannot support fan monitoring. PART NO: 90. 53F30. 001 DOC. [. . . ] The connector is equipped with a foolproof device. Make sure you plug in the right direction. +3. 3V -12V COM PS-ON COM 1 1 COM COM -5V Disable (default) Enable +5V +5V +3. 3V +3. 3V COM +5V COM +5V COM PWR OK 5VSB +12V 11. Connecting IDE and Floppy Cables The system comes with a slim-type CD-ROM drive and a slim-type floppy disk drive. Connect 40-pin, 80-wire IDE cable to IDE connector. A slim-type floppy disk drive is connected with a special design cable. Wrong orientation may cause system damage. Floppy drive connector ATA 100 IDE connector 13. Installing DIMM Sockets This motherboard supports Advanced ECC memory Controller, 168-pin PC100 / PC133 SDRAM, Virtual Channel Memory (VCM), and ESDRAM up to 3GB. Dimm3 Dimm2 Dimm1 RAID primary channel RAID secondary channel CD-ROM drive connector 14. Support 10/100 Mbps LAN Onboard On the strength of Intel 82550 PHY on board, which is a highly-integrated Platform LAN Connect device, it provides 10/100M bps Ethernet for office and home use, the Ethernet RJ45 connector is located on the back panel. The green LED indicates the link mode, it lights when linking to network and blinking when transferring data. The orange LED indicates the transfer mode, and it lights when data is transferring in 100Mbps mode. To enable or disable this function, you may simply adjust it through BIOS. 16. Back Panel The picture shown below indicates the functions of all connectors on the real panel. The connectors are all different in their shape or color. Please make sure you plug in the right direction. PS/2 Keyboard RJ45 LAN Jack Green/ACT Orange/Speed ATX Power Connector System event LED PS/2 Mouse COM1 VGA Connector 15. PCI Bus Slots The Fortress1100 has two 32-bit / 33 MHz PCI bus slots with a riser card. The riser card provides an easy way to plug the PCI card in the system. 17. Front Panel The picture shown below indicates the functions of LEDs of the front panel. The system provides two USB ports on the front panel. Please make sure you plug in the right direction. Riser Card System health LED Hard Disk LED Power LED USB Ports Reset Button Power Button 18. Power-On and Load BIOS Setup After you finish the setting of jumpers and connect correct cables. Power on and enter the BIOS Setup, press <Del> during POST (Power On Self Test). Choose "Load Default Setting" for recommended optimal performance. Del If you encounter any trouble to boot you system, follow the procedures accordingly to resolve the problem. Start Turn off the power and unplug the AC power cable, then remove all of the addon cards and cables, including VGA, IDE, FDD, COM1, COM2 and Printer. Make sure if the jumper settings for CPU and DRAMs are correct. Clear CMOS. Install the VGA card. [. . . ] http://www. aopen. com/tech/faq/default. htm 4 5 Download Software: Check out this table to get the latest updated BIOS/utility and drivers. http://www. aopen. com/tech/download/default. htm China ¦ã (ªÑ )¦³-¤½¥q Tel: 86-21-6225-8622 Fax: 86-21-6225-7926 Germany AOpen Computer GmbH. Tel: 49-2102-157700 Fax: 49-2102-157799 News Group: Our support engineer or professional users on the news group probably had answered your problem. http://www. aopen. com/tech/newsgrp/default. htm America AOpen America Inc. [. . . ]