User manual AOPEN VX2KUG

[. . . ] Should the programs prove defective following their purchase, the buyer (and not this company, its distributor, or its dealer) assumes the entire cost of all necessary servicing, repair, and any incidental or consequential damages resulting from any defect in the software. Further, this company reserves the right to revise this publication and to make changes from time to time in the contents hereof without obligation to notify any person of such revision or change. All brands or product names mentioned in this manual are trademarks or registered trademarks of their respective companies. Disclaimer FCC Statement FCC Class B Radio Frequency Interference Statement This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. [. . . ] External inputs for video capture: AV and S -video inputs for external video resources like cameras and VCRs. 1394 digital video input: 1394 input for high quality video source like DV camcorder. (need optional DV daughter board included) Wireless remote control included: Channels up/down, Volume up/down. Full motion video capture Still frame video capture External interface: 75 ohm IEC coaxial input (cable TV), composite (RCA) input, S-Video (SVHS) input, audio input, and line audio output 1 . 2 ­ WDM Ca p ture Driver Sup p ort n Windows ME n Windows 2000 n Windows XP 1 Chapter 1 ­ Introduction 1 . 3 ­ Mod el Comp a rison T a b le Model name 1394 NEC 3D TV Remote Composite S-Video Stereo DV Y/C System Control Input Input Input Separator Yes No Yes No Yes Yes Yes Yes Yes Yes Yes Yes VX2000S NTSC -DSNT8 VX2000S NTSC -NT8 VX2000S -DPB8 VX2000S -PB8 PAL Yes No Yes Yes Yes Yes PAL No No Yes Yes Yes Yes 2 Chapter 2 ­ VX2000 Series Setting C hapte r 2 ­ VX20 00 Se rie s Se tting 2 . 1 ­ VX 20 00 Series In terfa ce Overview PWR/RDY LED - Red light on when stand-by, green light on when ready, light out when power off. REC/PLAY LED - Blue light on when recording/playing, light out when stop. 1394 - DV input connect to i-link port on camcorder. USB2. 0 - Support USB2. 0 up to 15M bitrate and USB1. 1 up to 4M bitrate. Cable/Antenna - Cable or Antenna TV input. (Optional only for some model) R-out - Audio out for right channel. (Optional only for some model) CVBS-out - Composite video output. (Optional only for some model) SVideo-out - S-Video output. (Optional only for some model) 3 Chapter 2 ­ VX2000 Series Setting 2 . 2 ­ P a cka ge Conten ts l l l l l l l VX2000 Series Box Remote Controller AV cable USB cable Power adapter 1394 cable (optional) CD of VX2000 Series Software 2 . 3 ­ System R eq uirements l l l l l l l l l l IBM PC or compatible Pentium III 600MHz CPU or better processor Minimum 128 MB memory USB1. 1 port or USB2. 0 port VGA and with DirectDraw driver supporting 15 bit color or higher Microsoft Windows 2000/Me/XP TV antenna or cable from CATV Sound card Speakers for audio output CD-ROM drive 4 Chapter 2 ­ VX2000 Series Setting 2 . 4 ­ Ha rd wa re Insta lla t ion Note: 1. Connect either the composite or the S-Video cable to the VX2000 (never both) to avoid interference. External video sources you can connect to the VX2000 include a VCR, VCD/DVD player, or camcorder. 1. 6. Use an AV/S video/1394 cable to connect an external audio/video source to the VX2000. For TV input, plug the TV antenna cable into the VX2000. Connect the power adapter cable to the VX2000 and a grounded AC wall outlet; connect the USB cable to the appropriate connectors on the VX2000 and your PC. If the "Found New Hardware" dialog box appears, click Cancel. [. . . ] Click Install on the Ready to Install the Program dialog to begin installation. 7 Chapter 3 ­ Software Installation 10. When the installation has been completed, the Setup Options dialog box will appear. If you do not want to read the Readme file or go through the online registering procedure, deselect the appropriate options. Click Next to start the driver installation. [. . . ]