User manual APC SMART-UPS 750VA LCD 230V

[. . . ] 4 Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 Hardware Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 About the Web Configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 3. 1 3. 2 Access the Router . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] If data packets IP Port Range Source MAC IP Protocol ID include the IP address, the data packets are placed into the group. If data packets include the MAC address, the data packets are placed into the group. If data packets include the IP address, the data packets are placed into the group. You can choose TCP/UDP, TCP, UDP, ICMP or IGMP. Select this option to Activated/Deactivated the 4094 VID on the 4 different queues. VID (VLAN ID) is the identification of the VLAN, which is basically used by the Vlan ID Range standard 802. 1Q. It has 12 bits and allows the identification of 4096 (2^12) VLANs. Of the 4096 possible VIDs, a VID of 0 is used to identify priority frames and value 4095 (FFF) is reserved, so the maximum possible VLAN configurations are 4, 094. IPP/DS Field IP Precedence When IPP/TOS is set, select the IP Precedence ranging from 0 to 7. You may establish at most sixteen QoS rules. You may select Activated or Deactivated. Select what ATM VCs (0 to 7) will join the VLAN group. Also choose whether it will be tagged or untagged. Select what Ethernet ports (1 to 4) will join the VLAN group. Also Choose whether it will be tagged or untagged. Choose to assign the Wirless LAN to the VLAN group. 41 SMART-UPS 750VA LCD 230V User Manual 3. 5. 6 ADSL Click Advanced Setup > ADSL, the page shown in the following figure appears. The ADSL feature can be selected when you meet the physical connection problem. Please check the proper settings with your Internet service provider. The router supports these modulations: G. Lite, T1. 413, G. DMT, ADSL2, ADSL2+ and Auto Sync-Up. The router negotiates the modulation modes with the DSLAM. The following table describes the parameters and buttons of this page: Field ADSl Mode ADSL Type Description Choose Auto Sync-Up, ADSL2+, ADSL2, G. DMT, T1. 413 or G. lite. Choose ANNEX A, ANNEX I, ANNEX A/L, ANNEX M or ANNEX A/I/J/L/M. 3. 6 Access Management In the navigation bar, click Access Management. The Access Management page that is displayed contains ACL, Filter, SNMP, UPnP and DDNS. 3. 6. 1 ACL Choose Access Management > ACL, and the page shown in the following figure appears. [. . . ] UPnP broadcasts are only allowed on the LAN. Auto-Configure: UPnP network devices can automatically configure network addressing, announce their presence in the network to other UPnP devices and enable exchange of simple product and service descriptions. DDNS The Dynamic Domain Name System lets you use a static host name with a dynamic IP address. User should type the host name, user name and password assigned to your ADSL Router by your Dynamic DNS provider. User also can decide to turn on DYNDNS Wildcard or not. 3. 8. 5 Maintenance Choose Help > Maintenance, the page shown in the following figure appears. [. . . ]