User manual APPLE POWER MAC G5

[. . . ] Power Mac G5 User's Guide Includes setup, expansion, and troubleshooting information for your Power Mac G5 computer Apple Computer, Inc. Under the copyright laws, this manual may not be copied, in whole or in part, without the written consent of Apple. The Apple logo is a trademark of Apple Computer, Inc. , registered in the U. S. Use of the "keyboard" Apple logo (Option-Shift-K) for commercial purposes without the prior written consent of Apple may constitute trademark infringement and unfair competition in violation of federal and state laws. [. . . ] 6 Connect the power cable and the Serial ATA data cable to the drive, as shown in the illustration. Secure the drive in position by rotating the drive bay tab to its closed (horizontal) position. Disconnect the power cable from the top hard disk and pull the cable down to expose the middle power cable connector. Connect the middle power cable connector to the top drive, and the bottom cable connector to the bottom drive. Connect the data cable to the hard disk drive. 7 Replace the side panel, following the directions that begin on page 56. Replacing the Optical Drive Your computer comes with a SuperDrive. Follow these instructions to replace the SuperDrive drive in the optical drive bay. Important: Contact your drive manufacturer or consult the manufacturer's website to determine if your drive is set for cable select mode. Before installation, set the drive to cable select if the manufacturer hasn't already done so. 1 Open your computer and remove the side panel following the directions that begin on page 46. 60 Chapter 4 Working Inside Your Computer 2 Disconnect the optical drive ribbon cable from the logic board. Disconnect this cable from the main logic board in preparation for removing the optical drive. 3 Push the optical drive release levers out to release the drive. Swing open the two optical drive release levers. Chapter 4 Working Inside Your Computer 61 4 Carefully pull the drive a short distance out of the bay. 5 Disconnect the ribbon cable from the back of the original drive and gently pull the cable through the opening in the sheet metal divider at the back of the optical drive bay. Remove the ribbon cable from the back of the optical drive. Slide the other end of the ribbon cable up through the opening in the sheet metal divider inside the computer. Remove the metal shield from the optical drive. Remove the four metal optical drive guide pins from the bottom of the drive. Remove the power cable from the back of the optical drive. Remove the drive from the bay by inserting a couple of fingers through the ribbon cable opening and pushing against the drive. 6 Place two or three fingers through the opening at the back of the optical drive bay and push the drive out slightly so that you can remove it from the computer. 7 Remove the power cable from the drive. 8 Unscrew the four optical drive guide pins from the bottom of the original drive and attach them to the bottom of the replacement drive. 9 Remove the metal shield from the front of the drive and attach it to the front of the replacement drive. 62 Chapter 4 Working Inside Your Computer 10 Carefully remove the ribbon cable from the top of the original drive and transfer it to the replacement drive. Important: Reusable adhesive tape on the underside of the ribbon cable attaches the cable to the drive. When removing the cable from the original drive, be careful to keep the tape with the cable. 11 Attach the ribbon cable connector and the power cable to the back of the replacement drive. 12 Insert the drive part way into the drive bay and bend the free end of the ribbon cable, then pull it down through the opening in the sheet metal divider at the back of the optical drive bay. Attach the ribbon cable to the back of the optical drive. Slide the other end of the ribbon cable down through the opening in the sheet metal divider inside the computer. Install the metal shield on the optical drive. Install the four metal optical drive guide pins into the bottom of the drive. Attach the power cable to the back of the optical drive. Chapter 4 Working Inside Your Computer 63 13 Slide the drive the rest of the way into the drive bay, aligning the optical drive guide pins in the slots, and gently push the drive into place. 14 The optical drive release levers should close when the drive is installed correctly. If they don't close, gently push them. Push the optical drive into the computer so that the guide pins on the bottom of the drive engage the four slots inside the computer. Close the optical drive release levers completely when the drive is properly seated. 15 Attach the optical drive ribbon cable to its connector on the logic board. Reattach this cable to the connector on the main logic board. 16 Replace the side panel, following the directions that begin on page 56. 64 Chapter 4 Working Inside Your Computer Adding PCI Express Cards You can expand the capabilities of your Power Mac G5 by installing cards in the Peripheral Component Interconnect (PCI) Express slots. Your Power Mac G5 has four PCI Express slots that accommodate PCI Express cards and PCI Express graphics cards. About PCI Express Cards Your Power Mac G5 comes with a high-performance 16-lane (or 16x) PCI Express graphics card. This card, which contains the graphics processor unit (GPU) and provides the computer's display ports, is installed in slot1. The maximum bus width for each PCI Express slot is marked on the card guide. Slot 4 is a 4-lane (4x) slot, slot 3 is an 8-lane (8x) slot, slot 2 is a 4-lane (4x) slot, and slot 1 is a 16-lane (16x) slot. You can install additional PCI Express cards in any of the slots. [. . . ] Bluetooth Europe--EU Declaration of Conformity This wireless device complies with the specifications EN 300 328, EN 301-489, and EN 60950 following the provisions of the R&TTE Directive. Industry Canada Statement This Class B device meets all requirements of the Canadian interference-causing equipment regulations. Cet appareil numérique de la Class B respecte toutes les exigences du Règlement sur le matériel brouilleur du Canada. VCCI Class B Statement Europe - EU Declaration of Conformity Complies with European Directives 72/23/EEC, 89/ 336/EEC, and 99/5/EC. Laser Information Warning: Making adjustments or performing procedures other than those specified in your equipment's manual may result in hazardous radiation exposure. Do not attempt to disassemble the cabinet containing the laser. The laser beam used in this product is harmful to the eyes. [. . . ]