User manual APPLIED ENERGY ACTIVE 350S

[. . . ] REDRING ACTIVE 350S SMART TECHNOLOGY ELECTRIC SHOWER Installation and User Guide IMPORTANT: This booklet should be left with the user after installation and demonstration CONTENTS Section Page Introduction _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ 2 Important Safety Information _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ 2 How to use your Active 350S Shower (Detailed) _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ 3 How your Active 350S Shower Works _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ 4 How to maintain your Active 350S Shower _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ 5 What to do if things go wrong (1) Self Help _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ 5 What to do if things go wrong (2) Professional Service _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ 6 Redring After Sales Service _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ 6 How to install your Active 350S Shower _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ 7 Additional Accessories and Spare Parts _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ 10 Guarantee and Contact Details _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ 11 How to use your Active 350S Shower (Summary) _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ 12 INTRODUCTION Thank you for purchasing a quality Redring Active 350S Electric Shower manufactured in England. To enjoy your new shower at its best, please take time to read this manual thoroughly, and having done so, keep it handy for future reference. The Redring Active 350S is an electric shower incorporating our "Smart Technology" and a unique dual control combining on/off, power select and flow/temperature control. Your shower is designed to stabilise temperature changes caused by water pressure fluctuations. [. . . ] " (high)" setting may need to be selected. Select inner or outer only handset spray pattern. Thermal cut-out has operated after previous use (automatically resets when unit cools down) " (high)" setting may need to be selected. Check water pressure has not fallen so far as to let pressure switch cut out, e. g. The shower includes a shutdown feature that means the water will continue to flow for up to 7 seconds after " (stop)" has been selected. Please contact our spares department on 08709 000420 (UK only). Fitting instructions are provided with most spares 5 Water too HOT Water too COLD Spray pattern poor Water takes longer to heat up Water goes cold while using shower Water continues to flow when " (stop)" selected Broken parts WHAT TO DO IF THINGS GO WRONG (2) PROFESSIONAL SERVICE If the previous "Self Help" checks fail to restore the performance, you should seek professional help. The person who installed the shower is probably the best one to repair it and is certainly the person to contact if you have had a problem in the guarantee period. The following additional checklist is provided for the benefit of the qualified service person. Position the riser rail at the height recommended in diagram 5 and mark its position (also see separate accessories fitting instructions). Position the heater so that the top of the unit is horizontal and level with, or a maximum of 0. 6 metres (2ft) below the top of the riser rail. Choose a flat piece of wall to avoid the possibility of distorting the backplate thus making the front cover a poor fit. Adjust the position to get the most convenient arrangement taking the following into account. · The possible need to use the handset over the sink for hair washing etc. · · The heater must not be mounted in the direct spray from the handset. The handset must not be able to come into contact with used water in the cubicle, bath or basin. If it can, even after the hose has been retained by the soap dish (see separate accessories fitting instructions sheet) then a vacuum breaker must be fitted. 4. Fix the riser rail with screws provided (see separate instructions supplied with accessories). 5. Decide the position of the electrical cable into the unit. If top or bottom entry is chosen (according to diagram 4), cut away the walls in the backplate as shown in diagram 6. Decide the position of entry of the cold water pipe into the unit. If rear, please read the section on plumbing. [. . . ] Ensure the electricity and water are turned on to the unit. Turn outer knob "A" clockwise to the "Power Select" position of your choice. The water will flow, and the neon indicator light will glow. = High Power = Medium Power = Cold Shower 3. [. . . ]