User manual ARCAM CD192

[. . . ] Power sources Only connect the appliance to a power supply of the type described in the operating instructions or as marked on the appliance. 10. Power-cord protection Power supply cords should be routed so that they are not likely to be walked on or pinched by items placed upon or against them, paying particular attention to cords and plugs, and the point where they exit from the appliance. 11. Grounding Ensure that the grounding means of the appliance is not defeated. Important safety instructions This product is designed and manufactured to meet strict quality and safety standards. However, you should be aware of the following installation and operation precautions: 12. [. . . ] The second set of sockets can be used to connect to a second amplifier set up for multi-room use. 3 Coaxial digital output Use this socket if you are using a separate digital to analogue converter (DAC) or digital recorder. Connect to the DAC or recorder's digital input using a suitable 75 screened cable. CAUTION: Never connect the digital output socket to a conventional audio input. 4 Optical digital output Use this socket if you are using a separate DAC or digital recorder with an optical connection. Connect using a suitable optical cable. 5 Remote IR input These connections are for use in multi-room installations. In normal use there is no need to make any connections to these sockets. 6 and 12V Trigger input 7 Connecting to a power supply Wrong plug? Check that the plug supplied with the unit fits your supply and that your mains supply voltage agrees with the voltage setting (120V/230V) indicated on the rear panel of the unit. 2 If your mains supply voltage or mains plug is different, consult your Arcam dealer. Mains lead The appliance is normally supplied with a moulded mains plug already fitted to the lead. If for any reason the plug needs to be removed, it must be disposed of immediately and securely, as it is a potential shock hazard when inserted into the mains socket. Should you require a new mains lead, contact your Arcam dealer. Plugging in Push the plug (IEC line socket) of the power cable supplied with the unit into the socket POWER INLET) in the back of the unit. Make sure it is pushed in firmly. 1 (marked Put the plug on the other end of the cable into your power supply socket and switch the socket on. CD192 E-4 COMPACT DISC PLAYER CD192 24 BIT/192 kHz UPSAMPLING TECHNOLOGY LOAD PLAY STOP PAUSE TRACK POWER POWER Press this button to switch the CD player on and off. When first powered up with no CD installed the display shows `No disc'. 1 --NO DISC-- LOAD To install a CD, press LOAD (or OPEN on the remote control). The CD tray opens ­ it accepts 12cm and 8cm discs. Place the CD in the tray with the label facing uppermost. Press LOAD again (or press PLAY, or gently push the tray in 5mm) to close the tray. You will see the total number of tracks and total disc time. The display returns to `0' after a few seconds. The disc is now ready to play. 2 8 TRACK INDEX 1 52. 19 MIN SEC 12345 678 PLAY Press to play the CD. To restart from track 1, press STOP and then PLAY. Make sure your amplifier's input source selector is set to the correct input. 3 STOP Press to stop the CD playing. The display shows `0' and the number of tracks. 4 PAUSE Press to pause the disc (interrupt play). Press PLAY to resume play from the same point. 5 SEARCH Press to search backwards, or to search forwards for a particular passage within the currently playing track. If the player is in `PAUSE' mode the search is made at high speed with the sound muted. Press , or PLAY to stop the search action and resume playing. 6 SKIP TRACK To start a CD with a track other than the first, press To select another track during play, press or 7 or to locate the desired track. . The track is played automatically after selection. CDs with text Load You will see the total number of tracks and the total disc time with `CD TEXT' illuminated in the display. [. . . ] EC COUNTRIES ­ These products have been designed to comply with directive 89/336/EEC. USA ­ These products comply with FCC requirements. Laser radiation If an Arcam CD player is operated whilst the outer casing is removed, invisible laser radiation could cause eye damage. CD192 E-8 Worldwide Guarantee This entitles you to have the unit repaired free of charge, during the first two years after purchase, at any authorised Arcam distributor provided that it was originally purchased from an authorised Arcam dealer or distributor. The manufacturer can take no responsibility for defects arising from accident, misuse, abuse, wear and tear, neglect or through unauthorised adjustment and/or repair, neither can they accept responsibility for damage or loss occurring during transit to or from the person claiming under the guarantee. The warranty covers: Parts and labour costs for two years from the purchase date. After two years you must pay for both parts and labour costs. [. . . ]