User manual ARCAM CD36

[. . . ] Do not use the appliance near water ­ for example next to a bathtub, washbowl, kitchen sink, in a wet basement or near a swimming pool, etc. Object or liquid entry Take care that objects do not fall and liquids are not spilled into the enclosure through any openings. Liquid filled objects such as vases should not be placed on the equipment. Ventilation Do not place the equipment on a bed, sofa, rug or similar soft surface, or in an enclosed bookcase or cabinet, since ventilation may be impeded. [. . . ] Connect to the DAC or recorder's digital input using a suitable 75 screened cable. CAUTION: Never connect the digital output socket to a conventional audio input. 4 Optical digital output Use this socket if you are using a separate DAC or digital recorder with an optical connection. Connect using a suitable optical cable. 5 Remote IR input These connections are intended for use in multi-room installations. In normal use there is no need to make any connections to these sockets. TRIGGER IN ­ Connecting the 12V trigger output of an Arcam amplifier to this input will cause 6 and 12V Trigger input 7 the CD36 to switch automatically in and out of stand-by when the amplifier is switched off and on. REMOTE IN ­ This allows remote control signals to be received by the CD36 if the remote sensor is covered (or otherwise not `visible' to the remote control). An external sensor is used to receive the signals from the remote control, which are then fed to the CD36 (into this input) using a suitable cable. Remote control signals acceptable to the CD36 must be in modulated RC5 format, with a voltage level of between 5V and 15V. Both the trigger and remote control inputs require a mono 3. 5mm jack, with the tip active and the sleeve grounded. For the trigger in, the CD36 will come out of stand-by if the voltage on the tip is between 4V and 15V. Connecting to a power supply Mains lead The appliance is normally supplied with a moulded mains plug already fitted to the lead. If for any reason the plug needs to be removed, it must be disposed of immediately and securely, as it is a potential shock hazard when inserted into the mains socket. Check that the plug supplied with the unit fits your supply and that your mains supply voltage agrees with the voltage setting indicated on the rear panel of the unit. 2 If your mains supply voltage or mains plug is different, or you require a new lead, please consult your Arcam dealer. Plugging in CD36 E-4 Push the plug (IEC line socket) of the power cable supplied with the unit into the socket in the back of the unit. Put the plug on the other end of the cable into your power supply socket and switch the socket on. 1 CD36 COMPACT DISC PLAYER LOAD PLAY STOP PAUSE POWER POWER Press this button to switch the CD player on and off. When first powered up with no CD installed the display shows `No disc'. 7 --NO DISC-- LOAD To install a CD, press LOAD (or OPEN on the remote control). The CD tray opens ­ it accepts 12cm and 8cm discs. Place the CD in the tray with the label facing uppermost. Press LOAD again (or press PLAY, or gently push the tray in 5mm) to close the tray. You will see the total number of tracks and total disc time. The display returns to `0' after a few seconds. The disc is now ready to play. 1 8 TRACK INDEX 1 52. 19 MIN SEC 12345 678 PLAY Press to play the CD. To restart from track 1, press STOP and then PLAY. Make sure your amplifier's input source selector is set to the correct input. 2 STOP Press to stop the CD playing. The display shows `0' and the number of tracks. 3 PAUSE Press to pause the disc (interrupt play). Press PLAY to resume play from the same point. 4 SEARCH Press to search backwards, or to search forwards for a particular passage within the currently playing track. If the player is in `PAUSE' mode the search is made at high speed with the sound muted. [. . . ] EC COUNTRIES ­ These products have been designed to comply with directive 89/336/EEC. USA ­ These products comply with FCC requirements. Laser radiation If an Arcam CD player is operated whilst the outer casing is removed, invisible laser radiation could cause eye damage. CD36 E-8 Worldwide Guarantee This entitles you to have the unit repaired free of charge, during the first two years after purchase, at any authorised Arcam distributor provided that it was originally purchased from an authorised Arcam dealer or distributor. The manufacturer can take no responsibility for defects arising from accident, misuse, abuse, wear and tear, neglect or through unauthorised adjustment and/or repair, neither can they accept responsibility for damage or loss occurring during transit to or from the person claiming under the guarantee. The warranty covers: Parts and labour costs for two years from the purchase date. After two years you must pay for both parts and labour costs. [. . . ]