User manual ARGUS DC-1620

[. . . ] 9 Deleting Photos . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9 Flash . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10 Photo Storage. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10 Downloading Photos . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] Select installation destination and click the button for "next". -6- 13. Please do not click anything until it has finished. 14. Click "Finish" to finish ArcSoft software installation. 15. You have successfully installed "ArcSoft" software and "Argus Digital Camera" driver. You are now ready to start taking and editing photos. Taking Photos 1. Press shutter button for about 4 seconds to open the camera and "Hi -7- 000" will show on LCD at the back of camera. The camera will give out one "beep" sound indicating the camera having entered working state. Hi means no compression (VGA) (about 32 photos, as the case may be) Lo means compression (QVGA) (about 117 photos, as the case may be) 3. Hold the camera steadily, and press the shutter button to take photos. You will hear one beep , indicating your photo has been taken, you may continue taking photos. When the camera is fully loaded with photos, if you press the shutter button again, the buzzer will give out continuous beeps for alarming. When taking photos, the higher" beep " indicates the success of shooting while the lower one indicates the failure of shooting. Please hold camera steadily when you are taking photos. When taking photos in poor light, the camera will give out two continuous "beeps" , prompting the failure of shooting. Camera Function Control Power off the camera The camera will enter stand-by status automatically about 60 seconds later in case of no operation. Upon starting of camera, press Hi / Lo function button for 3 seconds, the continuous shoot icon " " will appear on the LCD display. Press the shutter button within 5 seconds to taking photos. The camera will take photos according to required mode specified at that time until you want -8- to stop shooting. Then the photos can be downloaded one by one. The camera will regain previous status after shooting and releasing of shutter button. Note: Under the continuous shooting mode, the shooting may fail due to poor lighting. Upon starting of camera, press delete function button for two times and select the " " icon shown on the LCD display. Pressing the shutter button again within 5 seconds will delete all the photos stored in the memory. [. . . ] A: There may be a collision with computer's peripheral devices. Please follow the steps below: (1) Select Argus Digital Camera in [Device Manager] and press right key / Uninstall (2) Remove USB cable (3) Restart computer (4) Reinsert USB cable 3. Q: After finishing installing software and connecting the camera to the computer, there's "unknown USB device" in Device Manager. A: Please check your camera has been connected well with your computer. If OK, please do the following steps: - 14 - (1) Uninstall Driver "Argus Digital Camera" (2) Reinstall Driver 4. Q: Can I connect the camera to the computer when I install the driver? [. . . ]