User manual ARRI ARRIFLEX 16S

[. . . ] Arriflex 16S Operating Instructions 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 Film Magazine (200 ft. ) Magazine Cover Lock Latch for Magazine Lock Camera Cover Lock Diopter Adjustment Ring Eyepiece Retaining Ring Lock for Diopter Adjustment Power Cable Lock Override Button for Buckle Switch Camera "ON" Switch Camera "OFF" Switch Cover Lock Spring Magazine Opening Cover Tachometer Footage Counter Frame Counter Power Connector Viewfinder Cover Door Accessory Shoe Focusing Lever Contour Hand Grip Re-Set for Footage Counter Re-Set for Frame Counter Motor Lock Lever Variable Speed Motor Rheostat To Control Camera Speed Inching Knob Eyelet for Carrying Strap Knurled Dis, Camera Take-Up Locking Levers for Torque Motor Torque Motor Knurled Disc, Magazine Take-Up Film Supply Counter Forward/Reverse Switch for Torque Motor Knurled Disc, Magazine Supply Knurled Disc, Camera Supply Lens Turret Lens Retaining Lever Filter Stage, Rotating Filter Stage, Stationary Matte Slot Matte Box Matte Box Beam Lock Screw for Matte Box Lock Screw for Matte Box Stages Diaphragm Ring Turret-Rotating Grips Eyelet for Carrying Strap The Arriflex 16S/B-GS [With 60-Cycle Generator and Automatic Startmarker] The 16S /B-GS is a special model of the basic Arrilflex 16 S/B. It is factory equipped with a 60-cycle generator, an automatic startmarker and a manually operated cue marker, designed to work with all ¼" tape recorders equipped with the pilotone system. The 60-Cycle Signal Generator A miniature generator is built into the camera. When the camera runs at 24 fps, the generator ooutput is a 60-cycle signal of approximately 1. 2 volts. This signal is the heart of all Piloton synchronizing systems. [. . . ] Use only the plastic skewer supplied with the camera and a clean untreated optical cloth. Registration Pin With the film gate opened, the registration pin can be seen just above the transport claw. Its function is to locate the film precisely and to hold it in place during the moment of exposure. The registration pin ensures rock-steady pictures, a repetitively precise film line, and increased tolerance against film pitch changes. Never force the registration pin in any way while cleaning the gate, only activate it by turning the motor inching knob [27]. Film Transport Claw The film transport claw engages the film from the front, the emulsion side. Watch its action by turning the inching knob (27) and note that it engages the film while the registration pin is lifting out of the perforation. This way, during the entire frame cycle, there is always one claw engaged for positive control of film. Mirror Reflex Shutter The mirror reflex shutter is the heart of the Arriflex reflex system. It rotates at a 45° angle between lens and film plane and reflects to the ground glass of the viewfinder exactly the same image as is registered on the film. All of the light rays reach the film through the lens without any interference while the shutter is open, and are alternately reflected to the ground glass only while the shutter is closed. Thus the film, as well as the eye, always gets 100% of the light transmitted by the taking lens. The effective shutter opening is 180° and gives the following exposure times at various speeds: 8 FPS ­ 1/16 sec. 48 FPS ­ 1/96 sec. As this table indicates, the exposure can be calculated for the camera speed by doubling the FPS figure and reading the result as a fraction of a second (180° shutter only). Tripod Sockets Two tripod threads, one 1/4" and one 3/8" size, are provided in the bottom of camera housing. This socket is made of tool steel and is a replaceable insert in the aluminum camera housing. Many standard tripod screws might be too long and trigger the built-in switch for the pistol grip. An excessively long tripod screw could even damage the switch housing inside the camera. The standard length for tripod screw is 7mm = 0. 280 inches. Camera Loading & Threading Turn cover lock (14) from "C" to "O" and lift cover. Lay cover down and be sure switch is in OFF position otherwise switch activating pin could get bent. Both spindles have an automatic lock to hold film spool in place in any camera position. To take film spool out, push button in center of spindle and tilt camera sideways. Open film gate by pressing latching knob inwards and swing the pressure pad assembly open on its hinges. Before threading film, open pressure roller assembly A by pressing button B. Swing off pressure roller 01, if necessary. Then arrest film by swinging back pressure roller D-1. [. . . ] If emulsion is hardened on film gate, remove it with a Q-tip dipped in acetone or alcohol. Be careful not to get any solvent on any optical surface. After cleaning, polish gently with chamois or other soft, clean optical cloth. From time to time, the lens mounts and the three lens sockets in the turret should be cleaned to remove dirt and dust. [. . . ]