User manual ARRI ARRIHEAD II

[. . . ] 13 Adjustable Tilt Drive . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14 Tilt Plate . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15 Transport . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19 Service and Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] Shift the camera on the tilt plate, until the "0" mark on the lower cradle falls in line with the witness mark. Keep a firm hold on the camera throughout, then resecure the three locking levers Á photo. friction locking lever for hand wheel locking lever for sliding base tilt lock gear selector switch 9 ARRIHEAD · The viewfinder and eyepiece will remain stationary during tilting, as long as the eyepiece leveler Á photo is fixed to both the threaded receptacle of the viewfinder extension (top) and the fixing bolt on the ARRIHEAD II Á photo. · Loosen the knurled screw Á photo, adjust the viewfinder to eye-level and re-tighten the knurled screw. knurled screw eyepiece leveler fixing bolt 10 ARRIHEAD · If required, slide the battery holder Á photo into the dove-tail guide Á photo on the right side of the ARRIHEAD II. battery holder dove-tail guide 11 ARRIHEAD Panning · Loosen the friction lever Á photo. · Slide the gear selector switch Á photo to the desired position. · Loosen the pan lock Á photo. · The ARRIHEAD II is now prepared for continuous 360° panning with use of the hand wheel Á photo. In order to avoid damaging the jaws of the friction lever and lock Á photo, it is essential to loosen both, before turning the hand wheel. pan lock friction locking lever for hand wheel gear selector switch hand wheel 12 ARRIHEAD Tilting · Loosen the friction lever Á photo. · Slide the gear selector switch Á photo to the desired position. · Loosen the two tilt locks Á photo. · The cradle of the ARRIHEAD II can now be tilted by turning the hand wheel Á photo. In order to avoid damaging the locking jaws of the friction lever and lock Á photo, it is essential to loosen both, before turning the hand wheel Á photo. gear selector switch friction locking lever for hand wheel tilt lock hand wheel 13 ARRIHEAD Adjustable Tilt Drive The tilt drive of the cradle can be pivoted horizontally 38 degrees counter clockwise. This preserves the full tilting rage of the ARRIHEAD II when using an ARRIFLEX 535 camera equipped with a 1000 ft (300 m) magazine. · Loosen the lock Á photo. · Swing the tilt drive to the desired position and retighten the lock Á photo. lock 14 ARRIHEAD Tilt Plate · The tilt plate Á photo pivots open to allow filming with extreme upward or downward tilt positions (up to 90° + or -). The tilt plate support is engaged in the corresponding bore holes. For safety, the camera should be removed while the tilt plate is adjusted. tilt plate 15 ARRIHEAD Filming with extreme upward angles · Push both release grips and raise the tilt plate Á photo as required. · Ensure that the locking pins of the support brackets Á photo are engaged exactly in the bore holes Á photo of the upper plate. · To allow easy mounting of the camera, set the tilt plate in a horizontal position. · Then mount the camera on the sliding base Á photo and lock in position. release grips support brackets bore holes tilt plate 16 ARRIHEAD release grips tilt plate sliding base bore holes support brackets 17 ARRIHEAD Filming with extreme downward angles · Push both release grips Á photo and raise the tilt plate as required. · Ensure that the locking pins of the support brackets Á photo are engaged exactly in the bore holes Á photo of the upper plate · To allow easy mounting of the camera, set the tilt plate in a horizontal position. · Mount the camera on the sliding base and lock in position. tilt plate release grips support brackets bore holes 18 ARRIHEAD Transport For transporting the ARRIHEAD II use the optionally available handles. · Remove the fixing screw Á photo. · Separate the two halfes of the handle. · Plug the rods Á photo into the center bore hole of the ARRIHEAD II. · Ensure that the four registration pins Á photo plug in to the other bore holes and retighten the fixing screws. rods registration pin fixing screw 19 ARRIHEAD Service and Maintenance For optimal performance it is essential that all ARRIHEAD II guides are kept clean. [. . . ] ARRI USA 617, Route 303 Blauvelt, New York 10913 phone: (914) 353 14 00 fax: (914) 425 12 50 E-mail: arriflex@arri. com ARRI USA 600 North Victory Blvd. Burbank, California 91502 phone: (818) 841 70 70 fax: (818) 848 40 28 E-mail: arriflex@arri. com GB . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . The Movie House 1-3 Airlinks, Spitfire Way Heston TW5 9 NR phone: (0208) 848 88 81 fax: (0208) 561 13 12 E-mail: sales@arri-gb. com 22 ARRIHEAD Italy . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Giovanni, Milano phone: (02) 26 22 71 75 fax: (02) 242 16 92 E-mail: info@arri. com ARRI ITALIA S. R. L. [. . . ]