User manual ARTEC T3A PRO

[. . . ] This device generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this device does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: · Connect the device to an electrical outlet on a circuit different from that to which the receiver is connected. consult a dealer or an experienced technician for help. [. . . ] Check the following items from the list to make sure that all accessories are included, and no damage or loss found. Features Input Terminal: Female 75 Ohm F-Type Connector Receiving Frequency: 57 ~ 861 MHz RF Channel: 2~69 Bandwidth: 6 MHZ Demodulator 8VSB Video Processing MPEG-2 Video Decoding (MP@ML, MP@HL) Input Format: Supports 18 Modes (1080p/1080i/720p/480p/480i) Output Format: NTSC 720x480i Composite Video out Audio Processing Dolby AC-3 Audio Decoding Digital Multi-Lingual Closed Caption Digital CC (Comply with EIA-708-B), English/Spanish/ French EPG Current program display by transparent graphic plane Power Input Voltage: 12V DC Power Consumption: 4. Power key Infrared receiver Power LED RF IN RF OUT CH 3/4 DATA PORT AV OUT (VIDEO / AUDIO-L / AUDIO-R) To be connected to the power adapter 10 DC IN 2 3 4 5 6 7 8 9 Descriptions Changes channels, Adjusts the volume levels, Browses, Press direction keys on the box at the same time to display the OSD menu, Press direction keys on the box at the same time to confirm Power ON / OFF Receives signals from the remote control LED lights when the power on To be connected to the antenna To be connected to the RF IN on the TV Toggles between the CH3 and CH4 Factory maintenance use To be connected to TV audio, Video input jack Open the battery cover by using the button on the back of the remote control. Select RF cable connection or AV cable (with RCA connector) connection connect TV according to your personal requirement, connect methods as follows: RF cable connection 1. Use a standard Audio/Video cable to connect the Audio/Video out jack on the Converter Box to the Audio/Video input jack on the DVD recorder. Follow the instructions (indicated in the "Connection Cable" section) to connect the power supply and other required peripheral devices. After the TV is on, press POWER on the remote control or POWER on the top of the Digital-to-Analog Converter Box to turn on the Digital-to-Analog Converter Box. After the Digital-to-Analog Converter Box is turned on, it will automatically lead you to the Install Guide. You can perform the following setup tasks after entering the "MENU" : Use the buttons to select input according to your personal requirement. Note: If you want to re-scan channel when the Lock System is set on the "On" mode, then you have to input the previous Lock Password number. Use the buttons to move the color block to define certain programs you wish to delete or add, press OK. Use the buttons to select Time Zone to the time zone where you are located. Use the buttons to select your desired Display Language. Use the buttons to select your desired Audio Language. Note: If your television is equipped with a caption feature, you may want to turn captioning off on your television in order to avoid double captions on the screen. Use the buttons to select the desired time or Off sleep timer. Note: If remote control has been inactive for more than 4 hours, the Converter Box will automatically go into sleep mode. Use the buttons to select your desired setting items, press OK. To reset the setting to the factory default, please press OK button, select Yes then press OK. Note: If you want to return to factory default settings when the Lock System is set on the "On" mode, then you have to input the previous Lock Password number. Enter your Password number by pressing the NUMBER buttons on the remote control. Use the buttons to select "Off" or "On" according to your personal requirement. [. . . ] Intermittent signal or Make sure your antenna is connected and is without damage. Outside the window or on the rooftop) with better reception. Make sure that the both ends of the AV cable are connected properly. Make sure the correct aspect ratio is selected. [. . . ]