User manual ARTHUR MARTIN AFT642W

[. . . ] It is passed back into the kitchen through the top of the kitchen cabinet. Before using for the first time, check to see whether the active charcoal filter is in place (see "Cleaning and Care"). d - Slide switch for , , Power selection" The power of the cooker hood can be adjusted to the intensity of the kitchen vapors and has four settings. The fourth setting (Intensive setting) should be selected for removing very strong kitchen vapors. low power. . . . . . . strong power e - Deflector plate The deflector plate can be pulled out to any extent up to its limit. The action of pulling the deflector plate out and pushing it in switches the cooker hood on and off respectively. [. . . ] The above ventilation restrictions and warnings do not apply if the exhaust hood is retrofitted with an air recirculation kit. 7 Warning and Safety instructions Warning and safety instructions Disposal of discarded appliances Before discarding an old appliance, disconnect its power cord to prevent it from becoming a hazard. SAVE THESE INSTRUCTIONS AND REVIEW THEM PERIODICALLY Throughout the manual, important safety items will be highlighted in boxes and should be read in conjunction with these "Warning and Safety instructions". 8 Operation Operation After cooking If, after finishing cooking, there are still cooking vapors in the kitchen, it is recommended that the cooker hood be left on for some minutes longer. Then switch the cooker hood off by: moving the slide switch for the fan and the cooktop illumination switch to the "0" position. Drop down the front control panel or lightshield. Set the slide switch for the fan to position "l". The cooker hood will operate at the setting the power selector is set to. Select a power setting strong enough to clear the air: 1 2 3 IS or push the deflector plate in. Setting 1-2 = for normal operation Setting 3-Intensive setting (IS) = for removing heavy cooking odors Switch on the cooktop illumination switch if required. 9 Cleaning and care Cleaning and care Before any cleaning or maintenance work, the extractor must be disconnected from the mains supply (switch off at the wall socket and remove plug or the fuse). Cleaning The cooker hood housing may be cleaned using hot water to which a little mild detergent has been added. Never use a cleaner which scours or contains chlorine, acids or soda. These would damage the surface of the cooker hood. Grease filters Re-usable metal grease filters are builtin which remove solid particles (oil, dust, etc. ) from the kitchen vapors, preventing soiling of the cooker hood. Unscrew the fixing screws at the left and right hand side. While doing so, hold the light cover securely and then take it out. 11 After Sales Service After Sales Service In the event of any fault which you cannot correct yourself please contact Your Miele Dealer or The Miele Service Department The address of the nearest Service Department is given on the back page. When contacting the Service Department, please quote the Model and Serial No. of the appliance, both of which are shown on the data plate. This is visible after removing the rear grease filter. 12 Electrical connection Electrical connection For CDN only: The cooker hoods are supplied with a 1. 50 m power supply cable ready for connection to an a. c. The distance between the top of the cooktop and the bottom of the cooker hood should be at least: 45 cm (18") above electric cooktops 65cm (26") above gas cooktops. Safety regulations prohibit the fitting of a cooker hood over solid fuel stoves. 15 Installation Installation Appliance dimensions Wall unit dimensions A: AFT642W i = 560; DA 272 i = 660; DA 292 i =860 B: AFT642W i = 595; DA 272 i = 695; DA 292 i =895 5 15 /16 415 /16 1313/16 25/16 65/8 A: AFT642W i = 562-568 = 22 1/8" - 22 3/8" DA 272 i = 662-668 = 26 1/16" - 26 5/16" DA 292 i = 862-868 = 33 15/16" - 34 3/16" B: AFT642W i = 600 = 23 5/8" DA 272 i = 700 = 27 5/8" DA 292 i = 900 = 35 1/2" 170-235 = 6 3/4" - 9 1/4" 135 = 5 3/8" 430 = 17" 110 = 4 11/16" 20 = 3/4" 285-350 = 11 1/4" - 13 7/8" 2 107 /16 A: AFT642W i = 22 1/16''; DA 272 i = 26''; DA 292 i =33 7/8'' B: AFT642W i = 23 5/8''; DA 272 i =27 9/16''; DA 292 i=35 7/16'' 13/16 The dividing wall must be removable to enable the cooker hood to be adjusted for height and depth. 515/16 107/16 max. 1615/16 * plus depth of control panel 16 Installation Installation Building in Take the dividing wall out of the wall unit. Push the brackets into the slots on the sides of the cooker hood. 19 mm ( 3/4 ") thick side walls: Secure the support tracks to both interior walls of the unit using two 3, 5 x 16 mm ( 5/8 ") screws, position as illustrated. 16 mm ( 5/8 ") thick side walls: Fasten the brackets in place on the cooker hood using the M 6 x 10 mm hexagonal bolts and washers. The thickness of the side walls must be taken into account. 17 Installation Installation Lift the cooker hood into the unit from below until the lugs of the brackets lie above the support tracks. [. . . ] Seek approval from the building inspector where necessary. Connection for extraction ­ The extraction ducting should be as short and straight as possible. ­ To ensure efficient air extraction the diameter of the exhaust ducting should not be less than 125 mm (5"). The use of flat ducting also reduces the air extraction efficiency. [. . . ]