User manual ARTHUR MARTIN AR3135I

[. . . ] réfrigérateurcongélateur AR 3135 I 2222 241-05 This document was created with FrameMaker 4. 0. 4 CONTENTS Warnings . page 20 21 22 22 22 22 22 23 24 24 25 25 25 25 25 25 26 26 27 28 28 28 28 28 Installation . Positioning . Electrical connection . . Installation of the appliance in a fitted kitchen unit . Instructions to assemble the refrigerator door to the kitchen unit door . [. . . ] Assemble the spacers and the bolts on the opposite side. Fig. 1 Positioning The appliance should be installed well away from sources of heat such as radiators, boilers, direct sunlight etc. ; best performance is obtained with ambient temperature between +16°C and +32°C (class N) or between +10°C and +32°C (class SN). The class of your appliance is shown on its rating plate. For building into kitchen units follow the special "Building-in" instructions given. Electrical connection Before plugging in, ensure that the voltage and frequency shown on the serial number plate correspond to your domestic power supply. Voltage can vary by ±6% of the rated voltage. For operation with different voltages, a suitably sized auto-transformer must be used. The power supply cable plug is provided with a contact for this purpose. If the domestic power supply socket is not earthed, connect the appliance to a separate earth in compliance with current regulations, consulting a specialist technician. The Manufacturer declines all responsibility if the above safety precautions are not observed. This appliance complies with EEC directive number 87/308 of 2/6/87 relative to radio interference suppression. D581 Building in Recess dimensions Height Depth Width 1780 mm 550 mm 560 mm For safety reasons, minimum ventilation must be as shown in the Fig. Attention: keep ventilation openings clear of obstruction. 50-min. 2 This appliance complies with the following E. E. C. Directives: - 73/23 EEC of 19. 2. 73 (Low Voltage Directive) and subsequent modifications; - 89/336 EEC of 3. 5. 89 (Electromagnetic Compatibility Directive) and subsequent modifications. D027 min. cm 2 200 Cleaning the interior Before using the appliance for the first time, wash the interior and all internal accessories with lukewarm water and some neutral soap so as to remove the typical smell of a brand-new product, then dry thoroughly. Do not use detergents or abrasive powders, as these will damage the finish. 22 Installation of the appliance in a fitted kitchen unit (Fig. 3) Drill the unit using a Ø 2. 5 mm drill (10 mm max. penetration); Fix the square fitting (1) to the appliance and apply the rubber seal; If the door is not already assembled fix the square fitting (2) to the refrigerator and fitting (3) to the unit column. 28mm Fig. 3 18mm 4 3 2 13mm 5 1 Ø 2, 5 Fit the refrigerator into the space recessing it by 48 mm in relation to the unit base (Fig. Fix the refrigerator with the screws (5) to the upper and lower part of the unit, after having inserted the fittings (6) under the lower hinges; Fix the square fitting (1) to the unit column and the square fittings (2-3) to each other, after inserting the clip (4). Insert the hinge cover. D612 5 5 6 Fig. 4 48mm D583 23 Instructions to assemble the refrigerator door to the kitchen unit door Position the runners (H) at the top and bottom of the inside of the kitchen unit as shown in Fig. 5 and mark the position of the external holes. [. . . ] The defrost water drains out through a trough into a special container at the back of the appliance, over the motor compressor, where it evaporates. It is important to periodically clean the defrost water drain hole in the middle of the refrigerator compartment channel to prevent the water overflowing and dripping onto the food inside. Use the special cleaner provided, which you will find already inserted into the drain hole. Fig. 11 The freezer compartment, however, will become progressively covered with frost. [. . . ]