User manual ARTHUR MARTIN DE0260W2

[. . . ] Ensure that the gas and electrical supply complies with the type stated on the rating plate, located near the gas supply pipe. Do not attempt to modify the hob in any way. Child Safety This hob is designed to be operated by adults. Do not allow children to play near or with the hob. Children should be kept away until it has cooled. [. . . ] B) are not obstructed. 7 Something Not Working? If the hob is not working correctly, please carry out the following checks before contacting your local Service Force Centre. SYMPTOM There is no spark when lighting the gas SOLUTION Check that the unit is plugged in and the electrical supply is switched on Check that the RCCB has not tripped (if fitted) Check the mains fuse has not blown Check the burner cap and crown have been replaced correctly, e. g. The gas ring burns unevenly Check the main jet is not blocked and the burner crown is clear of food particles. Check the burner cap and crown have been replaced correctly, e. g. after cleaning. If after all these checks, your hob still does not operate correctly, contact your local Service Force Centre. Please note that it will be necessary to provide proof of purchase for any inguarantee service calls. In-guarantee customers should ensure that the above checks have been made as the engineer will make a charge if the fault is not a mechanical or electrical breakdown. 8 Service and Spare Parts If you require spare parts or an engineer contact your local Service Force Centre by telephoning: 0870 5 929 929 Your call will be routed to your local Service Force Centre. For the address of your local Service Force Centre and further information about Service Force, please visit the website at www. serviceforce. co. uk When you contact the Service Centre, they will need the following information: 1. Your telephone number Clear and concise details of the fault The model and the serial number (see rating label on the back of this instruction booklet) Date of purchase Customer Care For general enquiries concerning your AEG-Electrolux appliance and for further information on AEG-Electrolux products, contact our Customer Care Department by letter or telephone at the address below or visit our website at www. aeg. co. uk Customer Care Department AEG-Electrolux Domestic Appliances 55 - 77 High Street Slough Berkshire SL1 1DZ Tel : 08705 350350* * calls to this number may be recorded for training purposes. 9 Guarantee Conditions Standard guarantee conditions We, AEG-Electrolux, undertake that if within 12 months of the date of the purchase this AEG-Electrolux appliance or any part thereof is proved to be defective by reason only of faulty workmanship or materials, we will, at our discretion repair or replace the same FREE OF CHARGE for labour, materials or carriage on condition that: · The appliance has been correctly installed and used only on the electricity or gas supply stated on the rating plate. · The appliance has been used for normal domestic purposes only, and in accordance with the manufacturer's operating and maintenance instructions. On the end of the shaft, which includes the G 1/2" threaded elbow, adjustment is fixed so that the washer is fitted between the components as shown in the diagram. Screw the parts together without using excessive force. Gas Connection Connection to the gas supply should be with either rigid or semi-rigid pipe, i. e. The connection should be suitable for connecting to R 1/2" (1/2 BSP male thread). When the final connection has been made, it is essential that a thorough leak test is carried out on the hob and installation. Ensure that the main connection pipe does not exert any strain on the hob. FO 0814 FO 0264 It is important to install the elbow correctly, with the shoulder on the end of the thread, fitted to the hob connecting pipe. Failure to ensure the correct assembly will cause leakage of gas. 13 Cut Out Size The dimensions of the cut-out are given in the diagram. 68 0 51 0 FO 2038 Building In Building over a cupboard or drawer If the hob is to be installed above a cupboard or drawer it will be necessary to fit a heat resistant board below the base of the hob on the underside of the work surface. It is also recommended to carry out the electrical connection to the hob as shown in diagrams 1 and 2 (see next page). 14 1 ON/OFF SWITCH ON/OFF SWITCH 2 FLEX OUTLET FLEX OUTLET FO 2563 FO 2564 Building over a kitchen unit with door Proper arrangements must be taken in designing the furniture unit, in order to avoid any contact with the bottom of the hob which can be heated when it is operated. The recommended solution is shown in diagram 3. The panel fitted under the hob ("a") should be easily removable to allow easy access if technical assistance is needed. The space behind the kitchen unit ("b") can be used for connections. 3 FO 2044 Dimensions are given in mm. 15 Fitting the Hob into the worktop Carry out the building in of the hob as follows: · put the seals supplied with the hob, on the edges of the cut out: place them exactly on the front and rear edge and at 50 mm. from the side edges, as shown in the diagram, taking care that the seals meet without overlapping; · place the hob in the cut out, taking care that it is centred; · fix the hob with the FO 2753 relevant fixing clamps and screws, as shown in the diagram. [. . . ] IGNITOR UNIT 18 Fault Finding Preliminary Electrical Systems Check START Isolate appliance and carry out: A: Earth Continuity check. Brown Blue Green Yellow Blue Brown Green Yellow NO YES Carry out: C: Polarity check. Carry out: D: Resistance to Earth check. Has inlet fuse blown? NO YES Electricity supply should now be satisfactory. PLUG (with cover removed) Inlet wiring faulty. Rectify any fault. Earth Wire Green/Yellow Neutral Wire Blue SOCKET (face view) () FUSE E( ) N L Isolate appliance and carry out: B: Insulation check. Rectify any fault including replacing fuses as necessary. 19 A. EARTH CONTINUITY CHECK Appliance must be electrically disconnected - meter set on (Ohms) x 1 scale and adjust zero if necessary. [. . . ]