User manual ASCOM TACTICAL OPENACCESS NODE C PRODUCT SHEET

[. . . ] It provides efficient connectivity between permanent and detached ad-hoc command and control facilities while allowing essential links to external public, strategic and legacy networks. LA S IO IS G product sheet: AscoM tActIcAL openAccess® Node c and Bps 2. 3 3 Technical Specification Network applications TAN T nodes inter-connect heterogeneous tactical networks, wired and wireless, IP and non-IP, into one unified All-IP communication domain. This enables a transparent and robust IP network for tactical environments, where users can communicate end-to-end without technology boundaries. TAN T supports multiple IP routing protocols, and can intelligently arbitrate between them. Multiple tactical network types like Ethernet, E1, SHDSL, Eurocom, CNR, or WLAN can be connected to TAN T. [. . . ] ISDN, Voice Trunking Eurocom, SIP, and H. 323 trunks are available for connecting TAN T to existing telephony Site-to-Site VPN infrastructure, including PSTN. Automatic Number Number flood searching allows for deploying flat Resolution dialplans. Multi-Protocol Voice Switch (PBX) Conferencing, hotline, MLPP (available July 2011) Voice Applications alternate routing (available July 2011). Fast The TAN T PBX can convert between all supported development of customer specific applications. VoIP Gateway voice technologies, allowing it to be used as VoIP FXS, FXO, ISDN (Euro-ISDN, QSIG), Eurocom gateway, e. g. Standards, Protocols, (a, b, c, STANAG), SIP, H. 323 (available March Codecs Multiple TAN T nodes can build a fully inter2011), IAX, G. 711, G. 723, GSM connected voice network. Flexible number Voice Trunking Security translation per voice trunk allows for integration into different numbering domains. Encrypted site-to-site IPSec VPNs supporting Routing algorithms optimized for low bandwidth, IPSec VPN multiple authentication methods. Available Integration of HF/ high latency radio networks are available and Q3/2011. VHF/LOS Radios allow to route traffic over wireless radio Firewall supporting filtering rules with access to networks. Stateless and stateful Firewall/NAT TAN T provides network services to locally filtering. Network address translation (NAT) for Network Services attached LANs, as DHCP, DNS, and NTP services. The built-in QoS engine allows for shaping traffic Import and management of PKI certificates and DiffServ Traffic Key Store with prioritization based on DiffServ or 802. 1D CRLs. All sensitive data in TAN T can be erased within few milliseconds by pressing emergency erase Data features Emergency Erase hardware or software key, also when node is TAN T provides non-blocking, line rate switching switched off. Switching / VLAN for all LAN Ethernet ports (copper and optical) System Management including support for 802. 1Q VLAN. TAN T routing engine supports static, OSPF, BGP, Web GUI for configuring and monitoring TAN T, PIM-SM, and IGMP routing protocols. Specialized remotely through IP network, or locally through routing algorithms are available for mesh laptop/PC connected to service Ethernet port. GUI IP Routing Management GUI networking and integration of radio networks. framework allows for fast development of Filtering and redistribution of routes is customer specific GUIs, e. g. TAN T includes 802. 11 a/b/g compliant wirelss XML-RPC compliant web services interface for WLAN Access Point LAN access point. [. . . ] TAN T hardware and software functions are IEEE 802. 3 Ethernet (Cu/FO), E1/T1 G. 703/704, Built-In Self-Testing tested on boot and on demand. Test reports allow Standards, Protocols SHDSL, Eurocom Data (Ascom proprietary), (BIT) for quick troubleshooting. 802. 11 a/b/g Local/Remote Standard UDP based syslog for remote and local Logging logging of system events. product sheet: AscoM tActIcAL openAccess® Node c and Bps 2. 3 4 Technical Specification Environmental conditions Temperature Relative Humidity Power consumption 50W typical ET P104: 3. 1 W ECOM P104: 4, 5W DSL P104: 5. 6 W AtMUX: 25 W peak, 10 W typical 0. . . +50 °C operation (with internal heating), Main unit -25. . . +70 °C storage 5. . . 95% (non condensing) operation 0. . . 99% (non condensing) storage Expansion units EMC (industrial usage) Emissions Immunity Mechanical 19" housing with 19" mounting adapters Size (LxHxD)/mm Weight Available interfaces Main Unit Management Ethernet Switched Ethernet Optical Ethernet Relay in Relay out Serial port 1 x 100Base-TX 4 x 1000Base-T 2 x 1000Base-X, multi mode or single mode fiber modules for 0, 5-160 km 1x 1x 1 x RS-232 420x89x300 (2U) 7 kg EN 55022 Class B EN 61000-6-2 Standard configuration The standard configurations include following units and externally available interfaces: openAccess Node C112: 1 x Main unit with: 1 x 10/100Base-TX 4 x 10/100/1000Base-T 2 x 1000Base-X, single mode 1 x Relay in 1 x Relay out 1 x RS-232 1 x ET P104 with: 4 x E1 1 x DSL P104 with: 4 x SHDSL 1 x AtMUX with: 3 x FXS 1 x FXO openAccess Node C107: 1 x Main unit with: 1 x 10/100Base-TX 4 x 10/100/1000Base-T 2 x 1000Base-X, single mode 1 x Relay in 1 x Relay out 1 x RS-232 Internal expansion units ET P104 DSL P104 AtMUX ECOM P104 Power Input voltage 22-50 VDC or 230 VAC with external power supply 8 x E1 per unit 4 x G. SHDSL (2-wire) per unit 1 x ET P104 with: 30 x a/b FXS or FXO per unit; configurable in groups 8 x E1 of 4; reserves 1xE1 port 1 x DSL P104 with: EUROCOM EES / D/1: 2xA (10 pin) or 4xB or 4xC 8 x SHDSL Although the information in this publication is represented in good faith and believed to be correct, Ascom makes no representations or warranties as to the completeness or accuracy of the information. In no event will be Ascom responsible for damages of any nature whatsover resulting from the use of or reliance upon the information contained in this document. [. . . ]