User manual ASCOM TACTICAL OPENACCESS NODE T PRODUCT SHEET

[. . . ] It is corrosion resistant and shock/vibration protected. Ascom tactical openAccess Node t can be used to create virtual LANs even over various transmission technologies, including ethernet, IsdN, shdsL, Los (Line-of-sight) and satellite infrastructure. Qos routing priorities can be defined as well as security levels set for secure and efficient traffic management. product sheet: AscoM tActIcAL openAccess® Node t and Bps 2. 3 2 Ascom Tactical openAccess Node T DN E1 ET H Vo IP AS W ET H M S LA The Tactical openAccess Node T is typically used as: WAS Edge Node LAS Access Node Access Node MS WAS LAS MS IOG Wide Area Subsystem Local Area Subsystem Mobile Subsystems (VHF/HF) Inter-Operable Gateway Ascom tactical openAccess Node t is a ruggedized interoperable voice and data network access element for tactical communication systems. It provides efficient connectivity between permanent and detached ad-hoc command and control facilities and mobile area sub-systems while allowing essential links to external public, strategic and legacy networks. S IO IS G product sheet: AscoM tActIcAL openAccess® Node t and Bps 2. 3 3 Technical Specification Network applications TAN T nodes inter-connect heterogeneous tactical networks, wired and wireless, IP and non-IP, into one unified All-IP communication domain. [. . . ] TAN T can be voice technologies, allowing it to be used as VoIP easily integrated into existing dialing plans. IAX trunks allow to setup bandwidth optimized Multiple TAN T nodes can build a fully interVoIP channel bundles between TAN T nodes. Flexible number Voice Trunking Eurocom, SIP, and H. 323 trunks are available for translation per voice trunk allows for integration connecting TAN T to existing telephony into different numbering domains. Routing algorithms optimized for low bandwidth, Automatic Number Number flood searching allows for deploying flat high latency radio networks are available and Resolution dialplans. allow to route traffic over wireless radio Conferencing, hotline, MLPP (available July 2011) networks. Voice Applications alternate routing (available July 2011). Fast TAN T provides network services to locally development of customer specific applications. attached LANs, as DHCP, DNS, and NTP services. The built-in QoS engine allows for shaping traffic Standards, Protocols, FXS, FXO, ISDN (Euro-ISDN, QSIG), Eurocom (a, b, c, STANAG), SIP, H. 323 (available March with prioritization based on DiffServ or 802. 1D Codecs 2011), IAX, G. 711, G. 723, GSM classification. Security TAN T provides non-blocking, line rate switching for all LAN Ethernet ports (copper and optical) including support for 802. 1Q VLAN. TAN T routing engine supports static, OSPF, BGP, PIM-SM, and IGMP routing protocols. Specialized routing algorithms are available for mesh networking and integration of radio networks. Filtering and redistribution of routes is supported. TAN T includes 802. 11 a/b/g compliant wirelss LAN access point. DiffServ standards compliant IP/Ethernet traffic conditioning, based on IP DSCP or Ethernet 802. 1p fields. Hardware traffic shaper works at gbit/s line rate. RFC compliant DNS server supporting dynamic DNS in combination with included DHCP server. Upstream DNS server (forwarders) and caching of DNS queries are supported. IPSec VPN Encrypted site-to-site IPSec VPNs supporting multiple authentication methods. Firewall supporting filtering rules with access to full IP packet headers. Network address translation (NAT) for private LANs. Import and management of PKI certificates and CRLs. [. . . ] I (rain and blowing rain 100mm/h, 40' per surface) MIL-STD-461E MIL-STD-461E Vibration Functional shock Shock, bench handling Available interfaces Main Unit Management Ethernet Switched Ethernet Optical Ethernet Relay in Relay out Serial port USB ET P104 DSL P104 AtMUX-r ECOM P104 Power Input voltage Power consumption Main unit Expansion units 58W without heating 81W with maximum heating ET P104: 3. 1W ECOM P104: 4. 5W DSL P104: 5. 6W AtMUX-r: 25W peak, 10W typical 22-50VDC or 230VAC with external power supply 1 x 100Base-TX 4 x 1000Base-T 2 x 1000Base-X, multi mode or single mode fiber modules for 0, 5-160 km 1x 1x 2 x RS-232 4x 8 x E1 per unit 4 x G. SHDSL (2-wire) per unit 30 x a/b FXS or FXO per unit; configurable in groups of 4; reserves 1xE1 port EUROCOM EES / D/1: 2xA (10 pin) or 4xB or 4xC MIL-STD-810F, method 514. 5, cat. 514. 5C-1, 5-500Hz, 40' per axis MIL-STD-810F, method 516. 5, proc. I, functional shock/operation, 30g/11 ms MIL-STD-810F, method 516. 5, proc. VI Management GUI Management Web Services Interface Configuration Profiles SNMP Software Maintenance Built-In Self-Testing (BIT) Local/Remote Logging Internal expansion units Environmental conditions Temperature Relative Humidity Waterproof EMC (industrial usage) Emissions Immunity Mechanical Watertight and hermetically sealed housing, carry handles or 19" mounting adapters, hardened for military use Size (LxHxD)/mm 400x110x265 Weight Cooling 10 kg Cooling functions without air exchange between inside and outside the housing. [. . . ]