User manual ASK PROXIMA DP2300

[. . . ] The projector lamp is not covered by this Warranty. Each Proxima product is manufactured from new parts, or new and some used parts. In some cases, the product may have been delivered to another end-user and then returned. In all cases, the product has undergone testing and quality inspection, and Proxima's full warranty terms apply. [. . . ] Plug it into the computer's monitor port. Insert the Y-cable's large, 25-pin connector marked LCD into the projector's COMPUTER port. Attach the appropriate video terminator to the MONITOR end of the Y-cable. For IBM compatibles, use part number C936; for Macintosh systems, use part number C935. Note: If your Desktop Projector is unable to project an image at the same time your laptop monitor displays an image, refer to your laptop documentation for information on switching between the internal screen and the video port. Special Configurations If your computer has an internal monitor but no external video capability (such as Macintosh Performa 575, PowerMac 5200, and certain PowerBooks), you need a video adapter card in order to attach the projector. Setup for a third-party adapter is identical to the procedures outlined in the previous section Desktop Computers. Contact your dealer, Proxima Customer Service, or third-party supplier for more information about an appropriate video adapter. User's Guide · 2­11 Chapter 2 · Detailed Setup RS­232 The RS­232 port allows you to use the optional Cyclops interactive pointer system or the Proxima Presentation Control Software. Instructions for connecting the appropriate serial or ADB cables are included with each of these products. VIDEO IN Audio/video-enabled models can project video from NTSC, PAL or SECAM sources (VCRs, laserdisc players, and video recorders). PROXIM A CR R­V RDE UT ECO IO O EO R AUD VID VIDE O OU T Figure 2-11 The Desktop Projector connected to a video source Note: If you would like to add video to audio-enabled models, you can order the Video Adapter Kit (A195); see Appendix B for ordering information. 2­12 · User's Guide Chapter 2 · Detailed Setup To connect an NTSC, PAL, or SECAM source to your Desktop Projector: 1. The composite audio/video cable (C497­6) is made up of 3 cables with yellow, red, and white RCA plugs. Insert the yellow RCA plug into the circular connector on your camcorder, laserdisc player, or VCR marked VIDEO OUT, TO MONITOR, or something similar. Insert the other yellow RCA plug into the projector's VIDEO IN port. The red and white cables are for audio input from the video source. Connect speaker A to speaker B using the cables supplied with the speaker system. Note: The projector's internal speakers can't be disabled or turned off. 2­16 · User's Guide Chapter 2 · Detailed Setup PROXIM A A B Figure 2-12 Connecting the Desktop Projector to external speakers External Stereo System To connect your Desktop Projector to an external stereo system: 1. Using the computer audio cable (C498­6), insert the mini jack end into the projector's AUDIO OUT connector. Insert the RCA connectors at the other end of the cable into the external amplifier's left and right AUDIO IN connectors. User's Guide · 2­17 Chapter 2 · Detailed Setup PROXIM A IER PLIF / AM T IVER RIGH ECE LEFT EO R STER Figure 2-13 Connecting the Desktop Projector to an external stereo system Powering Up Your Desktop Projector and external monitor (if you are using one) must be turned on before you turn on your computer, so that the computer properly senses each display during its boot-up sequence. Applying Power to the Projector On the rear connector panel of the projector, you'll find a power cord receptacle and an AC POWER switch. 2­18 · User's Guide Chapter 2 · Detailed Setup 3 2 1 Figure 2-14 Power receptacle (1), AC POWER switch (2), and circuit breaker reset switch (3) To power up the projector: 1. Plug the power cord into the Desktop Projector's power receptacle at the rear of the unit. CAUTION!Plug the AC power cord into the Desktop Projector BEFORE connecting it to an electrical outlet. If you plug the power cord into the wall first, you might damage the projector. Connect the power cord to a properly-grounded wall outlet or surge protector. Move the AC POWER switch to the ON position. The lamp comes on and the projector's fan begins to run. If you do not hear the fan, refer to Chapter 5. To raise or lower the projected image, tilt the mirror assembly to the appropriate angle. User's Guide · 2­19 Chapter 2 · Detailed Setup CAUTION! [. . . ] Be careful not to aim the stream of air directly into the fans' intake as this could force dust particles inside the unit. Reassemble the air filter assembly and replace it. Changing the Remote Control's Batteries To install or change the two AAA alkaline batteries in the remote control unit: 1. Locate the battery compartment at the lower rear of the case. Slide the cover off the battery compartment. [. . . ]