User manual ASK PROXIMA DP5800

[. . . ] Liquid Crystal Projector Model DP5800 USER'S GUIDE Please read this user's guide for fast setup and use of your new projector. After reading this guide, keep it in a safe place for future reference. DP5800 Features High brightness Highly efficient optical system with a metal halide lamp ensures high brightness. High resolution Three separate high-definition liquid crystal panels are used to provide sharp, clear pictures. Compact size and light weight for portability RGB output terminal RS232C communication Mouse emulation Power zoom and power focus Contents Page Symbols Used in this Guide . . . [. . . ] After the STANDBY/ON button is pressed, the fan will run for about 1 minute to cool the projector. 10 Projector Messages and Indicators On screen display The following messages may be displayed on the screen. Message NO SIGNAL IS DETECTED SYNC IS OUT OF RANGE CHANGE THE LAMP Check the input signal connection. The horizontal frequency of the input signal exceeds the range of the projector, and it cannot be displayed. Change the resolution of the input signal. Action Indicator display The ON indicator, LAMP indicator and TEMP indicator will light or blink in the following cases. Indicator status Lights orange ON indicator Blinks green Lights green Blinks orange Lights red LAMP indicator Blinks red Lights red TEMP indicator Blinks red Cooling fan failure Service the projector. Air filter detached Temperature inside too high Check the air filter. Meaning Standby mode Warming up Normal operation Cooling down Lamp cannot light Action -------------- ------------ -------------- ------------ -------------- ------------ -------------- ------------ Cool projector by power off for 20 minutes. The LAMP indicator will light when the lamp becomes too hot. Turn off the power and let the projector cool for 20 minutes. If the LAMP indicator still glows red, contact your dealer. 11 Using the Menus 2, 3 3 RIGHT RIGHT RISET RESET 2 1 MENU 1 menu STANDBY/ON 1 2 3 4 Press the MENU ( ) button or the MENU ON / OFF button. · Menus are displayed on the screen. Select the menu to be adjusted using the MENU ( buttons or the MENU STICK SWITCH. · The menu displayed in green is selected. ) Select the item to be adjusted using the MENU ( buttons or MENU STICK SWITCH. · The item displayed in green can be adjusted. ) The changes take effect. Storing your settings Settings can be saved for the VIDEO1, VIDEO2, RGB1 and RGB2 input terminals. These adjustments are saved after projector power is turned off. To return to the initial settings · Select the menu item to restore to the initial setting using the menu buttons or menu stick switch. · Select DEFAULT · Select the item to restore to the initial setting. · Press the RESET button a second time. SETUP VOL BRI CON SHA COL TIN INPUT IMAGE OPT. RESET `SETUP' DEFAULT CANCEL 12 Using the Menus (continued) SET UP Menu The SET UP menu lets you change the picture characteristics and position. The menus will be different for RGB and video signals. RGB signal Setup mumu SETUP INPUT IMAGE OPT. VIDEO signal Setup menu (video models only) SETUP INPUT IMAGE OPT. VOLUME BRIGHT CONTRAST V. POSIT H. POSIT H. PHASE H. SIZE 121 57 7 800 VOLUME BRIGHT CONTRAST SHARPNESS COLOR TINT Item VOLUME BRIGHT (BRIGHTNESS) CONTRAST SHARPNESS* COLOR* TINT* V. POSIT (V. POSITION) H. POSIT (H. POSITION) H. PHASE H. SIZE * Video models only Decrease Dark Lower Soft Less Red Range Increase Bright Higher Sharp More Green Moves the picture up or down. Widens or narrows the horizontal size of picture. NOTE: · TINT cannot be adjusted with PAL/SECAM video signal input (video models only). · TINT, COLOR and SHARPNESS cannot be adjusted with an RGB signal input. · V. POSIT, H. POSIT, H. PHASE and H. SIZE cannot be adjusted with a VIDEO signal input (video models only). 13 Using the Menus (continued) INPUT Menu Use this menu to select an input source. For Video inputs, you must also select a video format. SETUP INPUT IMAGE OPT. SETUP INPUT IMAGE OPT. RGB1 RGB2 VIDEO1 VIDEO2 TEST PATTERN RGB1 RGB2 VIDEO1 VIDEO2 TEST PATTERN SYSTEM AUTO NTSC PAL SECAM Item RGB1 RGB2 VIDEO1* VIDEO2* TEST PATTERN SYSTEM * Video models only. Options Selects the RGB 1 terminal. Selects the video signal systems. IMAGE Menu The IMAGE menu controls picture inversion, Size, Reveal and Blanking. SETUP INPUT IMAGE OPT. SETUP INPUT IMAGE OPT. MIRROR BLANK REVEAL DISP. SIZE MESSAGE MIRROR NORMAL H : INVERT V : INVERT H&V : INVERT SETUP INPUT IMAGE OPT. SETUP INPUT IMAGE OPT. BLANK WHITE BLUE BLACK REVEAL FAST MEDIUM SLOW 14 Using the Menus (continued) Select normal or expanded image size. SETUP INPUT IMAGE OPT. SIZE NORMAL SMALL MESSAGE TURN ON TURN OFF Adjustment Item MIRROR BLANK REVEAL Details of adjustment Inverts the picture horizontally or vertically for ceiling or rear screen projection. H : INVERT Inverts the picture horizontally. V : INTERT Inverts the picture vertically. [. . . ] · Replace the lamp with a new one. Turn off the power and let it rest for 20 minutes. Reseat the air filter. Page 9 6 6, 7, 9 No picture or sound. · The setting of the input source is not correct. · Wiring to the projector is not correct. 6, 24 6, 24 6, 7 6, 7 6, 24 12, 13 12, 13 12, 13 26 6, 7, 9 11, 26 11 11, 26 Picture is displayed with no sound. · Wiring to the projector is not correct. [. . . ]