User manual ASK PROXIMA DP6860

[. . . ] In Focus Corporation: 27700B SW Parkway Avenue · Wilsonville , Oregon 97070-9215 Phone: 503-685-8888 · 1-800-294-6400 · Fax: 503-685-8887 In Europe: Olympia l · NL-1213 NS Hilversum, The Netherlands Phone: (31) 35 6474000 · Fax: (31) 35 6423999 Freephone: 008000 4636287 (008000 INFOCUS) In Asia: 238A Thomson Road · #18-01/04 Novena Square Singapore 307684 · Telephone: (65) 334-9005 · Fax: (65) 334-4525 User's Guide 010-0298-00 Part No. 010-0298-00 DP6860 User's Manual. qxd Printed in Japan 010-0298-00 QR50271 w w w. c o m 1. 800. 294. 6400 DP6860 Desktop Projector P R ESEN TAT I ON SOL U T I ON S Liquid Crystal Projector Thank you for purchasing this liquid crystal projector. WARNING · Please read the accompanying manual "SAFETY INSTRUCTIONS" and this "USER'S GUIDE" thoroughly to ensure correct usage through understanding. After reading, store this instruction manual in a safe place for future reference. [. . . ] Input Menu Item Description Automatic Adjustment at RGB Input: Select the EXECUTE with the button. Horizontal position (H. POSIT), vertical position (V. POSIT), clock phase (H. PHASE), and horizontal size (H. SIZE) are automatically adjusted. Use with the window at maximum size in the application display. Automatic Adjustment at Video Input: Select the EXECUTE with the button. A signal type appropriate for the input signal is selected automatically when EXECUTE is selected automatically. Valid only when AUTO is set for VIDEO on the menu. · This operation requires approximately 10 seconds. It may not function correctly with some input signals. Pressing the AUTO button in this case may correct this problem. · This function is the same as for the AUTO function in Basic operation. AUTO RGB Displays RGB Input Frequency: Displays the horizontal and vertical sync signal frequencies for RGB input. · Valid only at RGB input. Select Video Signal Type: Select the signal type with the and buttons. Select NTSC, PAL, SECAM, NTSC4. 43, M-PAL, or N-PAL as appropriate for the input signal. The selection of AUTO enables and executes the function AUTO (Automatic Adjustment at Video Input), except for the N-PAL input. VIDEO (**) · Use this function when the image becomes unstable (eg. the image becomes irregular, or lacks color) at VIDEO/S-VIDEO input. · Automatic Adjustment requires approximately ten seconds. It may not function correctly with some input signals. Pressing the AUTO button in this case may correct this problem except for the N-PAL input. · For the COMPONENT VIDEO input, this function is not effective and the signal type is distinguished automatically. Menu for the signal of HDTV. VIDEO NR (**) Progressive (**) Set/Clear Noise Reduction Mode: Select the TURN ON / TURN OFF with the / button. When the TURN ON is selected, the NR mode is active and the noise on screen of the video input will be reduced. Select Progressive Mode: Select the mode suitable for the input signal with the and buttons. The TV mode and the CINEMA mode convert the interlaced video signal into the progressive signal. The CINEMA mode is adptable for 2-3 Pull-Down system. · Use this function to raise resolution, at the interlaced video input except HDTV signals. BLACK(**) Set/Clear Black Enhancement Mode: Select the TURN ON / TURN OFF with the / button. [. . . ] Set the power switch to [O] and wait for 20 minutes until the equipment has cooled sufficiently. ENGLISH-21 ENGLISH Indicators Message TROUBLESHOOTING (continued) Symptom Before requesting repair, check in accordance with the following chart. If the situation cannot be corrected, then contact your dealer. Table 11. Symptom Symptom The power is not turned on. Possible cause The main power switch is not turned on. The input is not correctly set. Remedy Turn on the main power switch. [. . . ]