User manual ASK PROXIMA DP9100

[. . . ] USER'S GUIDE Multimedia LCD Projector (Not actual front cover) WARRANTY Proxima Corporation warrants that the Proxima® Desktop ProjectorTM product manufactured by Proxima is free from defects in materials and workmanship under normal use during the Warranty Period. The Warranty Period commences on the day of purchase by the end-user. The projector lamp is not covered by this Warranty. Each Proxima product is manufactured from new parts, or new and some used parts. [. . . ] Sets the break timer interval, from 1 - 60 minutes. Sets the speed of the mouse. 3-2 Chapter Three The Cyclops menu Menus Tools Calibrate No Calibrate Calibrate Button Left Right Cyclops Input Source Center None Image Audio Projector Preferences Advanced Figure 3-3, The Cyclops menu USE THIS OPTION. . . Calibrate Button . . . TO DO THIS: Starts the Cyclops calibration procedure. Sets the Cyclops wand or laser pointer to emulate a left, right, or center mouse button (or none). Menus and Keys 3-3 The Input Source menu Menus Tools Cyclops Source Select Computer Video 1 SourceMode Cancel Input Measurements VSync: 0. 00 Hz HSync: 0. 00 KHz Lines: 0 Sense: HHHH Select Input Source Image Audio Projector Preferences S-Video 1 Video 2 S-Video 2 MediaExpress EWS1 (140 MHz) 1280 x 1024 81. 97 KHz 76 HZ EWS2 (130 MHz) 1280 x 1024 81. 25 KHz 76 Hz EWS3 (135 MHz) 1280 x 1024 80 KHz 76 Hz Current Mode: Advanced Figure 3-4, The Input source menu USE THIS OPTION. . . Source Select . . . TO DO THIS: Select the input source: · Computer · Video 1 · S-Video 1 · Video 2 · S-Video 2 · MediaExpress (optional) Source Mode Select from a list of video or computer standards: · NTSC · PAL · SECAM · Computer compatibility Input Measurements View projector readings for the selected input source: · VSync (vertical sync frequency) · HSync (horizontal sync frequency) · Lines (number of h-sync pulses per v-sync) · Sense (monitor input sense line levels) 3-4 Chapter Three The Image menu (computer or MediaExpress input source) Menus Tools Cyclops Sync DotClk. Bright Contrast Red Green Blue Factory Default No Reset Reset Interlace Even Odd Input Source Image Audio Projector Preferences Advanced Figure 3-5, The Image menu USE THIS OPTION. . . *Sync *DotClk Bright Contrast Red Green Blue *Factory Default Interlace . . . TO DO THIS: Adjusts the sync setting. Resets the source mode to the initial factory settings. Sets the interlace even/odd frame assignment: · Even sets frame 0 as even. · Odd sets frame 0 as odd. * Not available in MediaExpress mode. Menus and Keys 3-5 The Image menu (video or S-Video input source) Menus Tools Cyclops Contrast Bright Tint Saturation Input Source Image Audio Projector Preferences Advanced Figure 3-6, The Image menu USE THIS OPTION. . . Contrast Bright Tint Saturation . . . TO DO THIS: Adjusts the video contrast. Adjusts the video color saturation. 3-6 Chapter Three The Audio menu Menus Tools Cyclops Volume Mute Normal Mute Balance Bass Treble Fade Mic. Volume Audio Mode Stereo Mono Input Source Image Audio Projector Preferences Advanced Figure 3-7, The Audio menu USE THIS OPTION. . . Volume Mute Balance Bass Treble Fade Mic. Volume Audio Mode . . . TO DO THIS: Adjusts the audio volume. Switches between Stereo and Mono mode. Menus and Keys 3-7 The Projector menu Menus Tools Cyclops Projection Front Lamp Hours Lamp Hours 65:25:54 No Reset Reset Rear Input Source Image Audio Projector Preferences Advanced Figure 3-8, The Projector menu USE THIS OPTION. . . Projection Lamp Hours . . . TO DO THIS: Switches between front and rear projection. Use this option after you change the lamp. Lamp Hours Displays the number of hours elapsed on the lamp hours counter. 3-8 Chapter Three The Preferences menu Menus Tools Cyclops Colors 226K Millions Language English Deutsch On-Screen Display Hide Prog. Key1 Fit-to-View LightBoard Reverse Clear Prog. Key2 Fit-toView LightBoard Reverse Clear Input Source Image Audio Projector Francais Español Italiano Freeze Freeze Preferences Advanced Figure 3-9, The Preferences menu USE THIS OPTION. . . Colors Language On-screen . . . TO DO THIS: Sets the number of colors to use. Sets the default language for the menus. Displays or hides the slide bars for sync, volume, contrast, tint, horizontal position, and vertical position. Prog 1 Sets an operation for the Prog 1 key on the remote control. Choose from the following options (described elsewhere in this guide): · Fit-to-View · LightBoard · Reverse · Clear · Freeze · Colors · WhiteBoard · BlackBoard · Host · Title screen Prog 2 Sets an operation for the Prog 2 key on the remote control (same choices as Prog 1 key). Menus and Keys 3-9 The Advanced menu Menus Tools Cyclops User Defaults Horiz. Pos. VCO Gain Sense 3 High Sense 2 High Sense 1 High Sense 0 High User A User B Low Low Low Low Input Source Image Audio Projector Preferences Advanced Figure 3-10, The Advanced menu USE THIS OPTION. . . User . . . TO DO THIS: Sets a user profile of projector settings: · Defaults · User A (user defined) · User B (user defined) Hor. (Vertical) Pos (Position) VCO gain Sense 3, 2, 1, and 0 Adjusts the horizontal position of the image on the screen. Adjust the vertical position of the image on the screen. Sets the VCO gain parameter of the PLL. Set the level of the four sense pins: · High does not drive this pin. See Appendix C, Sense Lines for more information. 3-10 Chapter Three Chapter 4 Cyclops F/X Your projector comes with Cyclops F/X -- software effects that you can use to make your presentations more interesting and effective. For example, you can use the Spotlight to call attention to specific areas on the image, use the Zoom or Magnify effects to focus on important information in the image, or use See-it/Show-it to preview images on your computer without distracting your audience. You can use Cyclops F/X with either the that came with your emote r pr ojector or the optional Cyclops interactive pointer system, or both a same time. Note: Cyclops F/X is not available for UNIX systems. Note: You cannot use Cyclops F/X with the MediaExpress system. To use Cyclops F/X, follow these steps (details are covered throughout this chapter): 1 Use the serial cable appropriate for your system (PCs: C936-6 or Macs: C470-6) to connect the serial port on your computer to the CYCLOPS port on the projector. C Cyclops Figure 4-1, Cyclops port on the projector 2 Install the Cyclops F/X software. [. . . ] The absence of sense line information causes some display cards to output a default video signal, and actually prevents some video cards from outputting video at all. Sense line information is only required when you are using a system without a monitor and the video card defaults to an incompatible resolution. Sense line information can be found in the technical documentation that came with your computer. CONFIGURING THE DESKTOP PROJECTOR 9100 1 Determine the default resolution for your video system. 2 Gather sense line information from your computer documentation or from your video card documentation. [. . . ]