User manual ASK PROXIMA IMPRESSION A10

[. . . ] QUICK SET-UP ENGLISH The following steps will quickly lead you through set-up and adjustments for the projector connected to a single computer. For connection to a second computer, please consult the Making the Connections section. The sequence numbers refer to the drawing of the quick set-up. SETTING UP POWER OFF (1) Switch off all equipment before connecting. COMPUTER (2) Connect the computer to the COMPUTER 1 (or 2) connector using the computer cable. [. . . ] If necessary, fine adjust the height by screwing the feet either direction. Zoom Focus Foot-release button Foot-release button Adjustable feet 2. RESET in most cases automatically adjusts the image position, width (WIDTH) and stability (TUNE). If RESET fails to adjust the image 16 USER GUIDE XGA LCD PROJECTOR correctly, see WIDTH, POSITION and TUNE below. RESET is automatically activated when a new source is connected. CONTRAST and BRIGHTNESS may be adjusted according to your personal taste, the image and the viewing conditions. The controls are directly accessible on the projector keyboard. The frequency controls the width of the image. A wrong frequency setting can be seen as equally spaced, vertical stripes or irregularities in the pattern displayed. Press the MENU key, ADVANCED, PICTURE, WIDTH and press SELECT. Adjust the value up or down using the trackball or keyboard cursor controls, observing that the amount of vertical stripes reduces, until the distortion is gone. You may still have an unstable image, please see the next section. POSITION the image correctly by accessing ADVANCED, PICTURE, POSITION, then press SELECT and adjust position with the trackball or keyboard cursor controls 6. In the menu, select ADVANCED, PICTURE, TUNE and press SELECT. Set-up should be done once with the source(s) you are using most frequently. Allow some minutes for the unit to warm up before adjusting the settings. Most settings will be memorized individually for each source for future use. 17 USER GUIDE XGA LCD PROJECTOR 8 USING THE PROJECTOR The projector has a set of features and functions you should familiarize with in order to get the most out of using the unit. 8. 1 REMOTE CONTROL The remote control is used to adjust the projector for the best possible image, either directly or through the menu system. It is also used during presentations for computer mouse control and with special presentation tools. The remote control may be pointed directly at the projector front or rear, where the receivers are situated, or indirectly by pointing at the projection screen. When pointing at the screen, point at an angle that reflects the beam towards the projector. The remote control can also be physically connected to the projector using an optional cable with standard 2. 5 mm mini-jack connectors. LED Indicator Wire Connection Trackball Left Key (Select) ON/OFF Switch Right Key The trackball is by default controlling the computer mouse (if the mouse cable is connected properly). With the function keys BLACK, MAGNIFY and MENU, the mouse control is disabled. In the menu system, the trackball is used for navigation between the different alternatives, and when a function is selected, the trackball is used for adjustment of that function. 18 USER GUIDE XGA LCD PROJECTOR 8. 1. 1 REMOTE CONTROL KEYS The following table describes each key in detail. [. . . ] This projector is designed for indoor use and should not be operated or stored in conditions outside the general environmental limits given in section below, as this may lead to permanent damage and will violate any warranties. 12. 1 GENERAL ENVIRONMENTAL LIMITS -20 - 60° (-4 - 140 F), sea level C 10 - 90 % relative humidity, noncondensing 10 ­ 35° (50 - 95 F) ambient, sea level C 20 - 80 % relative humidity STORAGE TEMPERATURE STORAGE HUMIDITY OPERATING TEMPERATURE OPERATING HUMIDITY Allow for slow acclimatization after storing at extreme temperatures and humidities, to avoid condensation. Should condensation appear, leave the projector unit in a controlled environment within the operating limits until the condensation has evaporated before using the projector. 35 USER GUIDE XGA LCD PROJECTOR 12. 2 PROJECTOR UNIT 118 x 262 x 312 (399 incl. Manual zoom and focus lens 1. 3 zoom ratio f 55-72 mm F 2. 0 ­ 2. 3 0. 74 - 7. 69 m / 29 - 303 inches (wide) 0. 56 ­ 7. 69 m / 23 - 303 inches (Tele) 1. 2 - 12 m / 3. 9 ­ 39. 3 ft 12 degrees 150 W UHP 1. 3"polysilicon TFT LCD 16. 7 million 300:1 1024 x 768 x 3 10 (max) 12 - 150 MHz 15 - 100 kHz 43. 5 - 130 Hz 0 - 1 Vpp 1V RMS 2 x 5 W speakers · · · · CE UL cUL FCC, Subpart J, Part 15 PROJECTOR DIMENSIONS (H x W x L) PROJECTOR WEIGHT PROJECTION LENS IMAGE SIZE PROJECTION DISTANCE ANTI-KEYSTONE CORRECTION PROJECTION LAMP LIGHT VALVE COLOR RESOLUTION CONTRAST RATIO PIXEL RESOLUTION DEFECTIVE PIXELS VIDEO FREQUENCY HORIZONTAL SYNC VERTICAL SYNC COMPUTER INPUT AUDIO INPUT SPEAKERS CONFORMANCE 12. 3 POWER SUPPLY 100 - 120 VAC, 60 Hz, +/- 10 % 220 - 240 VAC, 50 Hz, +/- 10 % 250 W operating DUAL VOLTAGE 36 USER GUIDE XGA LCD PROJECTOR 12. 4 REMOTE CONTROL 27 x 48 x 140 mm / 1. 06 x 1. 89 x 5. 51 inch 96 g / 0. 21 lb. (with batteries) 2 pcs LR03/AAA 1. 5V penlight 15 m (50 ft)/Using cable 20 m (66 ft) Microsoft 2-key serial, MAC, PS/2, USB CE, FCC UNIT SIZE (H x W x L) UNIT WEIGHT BATTERIES FUNCTIONAL RANGE COMPATIBILITY CONFORMANCE 12. 5 COMPATIBILITY The projector is compatible with the interfaces and resolutions shown below, some of which are predefined. [. . . ]