User manual ASK PROXIMA IMPRESSION A2 Quick Setup

[. . . ] QUICK SET-UP ENGLISH The following steps will quickly lead you through set-up and adjustments for the projector connected to a single computer. The sequence numbers refer to the drawing of the quick setup. Before connecting, please remember to switch off the computer and disconnect the projector power cord. SETTING UP POWER OFF (1) Switch off all equipment before connecting. COMPUTER (2) Connect to the computer graphics port. [. . . ] POSITION the image correctly by accessing SET-UP, POSITION, then press ENTER and adjust position with the trackball or keyboard cursor controls 6. In the menu, select SET-UP, TUNE and press ENTER. Set-up should be done once with the source(s) you are using most frequently. Allow some minutes for the unit to warm up before adjusting the settings. Most settings will be memorized individually for each source for future use. 16 USER GUIDE SVGA LCD PROJECTOR 8 USING THE PROJECTOR The projector has a set of features and functions you should familiarize with in order to get the most out of using the unit. 8. 1 REMOTE CONTROL The remote control is used to adjust the projector for the best possible image, either directly or through the menu system. It is also used during presentations for computer mouse control and with special presentation tools. The remote control may be pointed directly at the projector front or rear, where the receivers are situated, or indirectly by pointing at the projection screen. When pointing at the screen, point at an angle that reflects the beam towards the projector. 3 1 2 4 6 8 7 5 1. Bottom Key (Drag) Not applicable for this product 17 USER GUIDE SVGA LCD PROJECTOR The trackball is by default controlling the computer mouse (if the mouse cable is connected properly). With some functions, like POINTER, MASK and in the menu system, the mouse control is disabled. In the menu system, the trackball is used for navigation between the different alternatives, and when a function is selected, the trackball is used for adjustment of that function. Turn on the remote control by sliding the ON/OFF-switch to ON position. To avoid draining the batteries, turn the remote control OFF after use. 8. 1. 1 REMOTE CONTROL KEYS The following table describes each key in detail. Some functions are memorized, while other functions are only momentary. The MEM column indicates whether the function setting is memorized. ON/OFF CONTR BRIGHT VOLUME POWER Switches the remote control on/off (battery save) Adjusts contrast. Turns the projector into either operating or standby mode. In standby mode the projection lamp is switched off. Automatically adjusts the image correctly Applies a mask to the image, which can be moved up and down using the trackball. This key may be programmed to any one of the menu controls. Holds the image projected on the screen. [. . . ] This projector is designed for indoor use and should not be operated or stored in conditions outside the general environmental limits given in section below, as this may lead to permanent damage and will violate any warranties. 12. 1 GENERAL ENVIRONMENTAL LIMITS -20 - 60° (-4 - 140 F), sea level C 10 - 90 % relative humidity, noncondensing 10 - 35° (50 - 95 F) ambient, sea level C 20 - 80 % relative humidity STORAGE TEMPERATURE STORAGE HUMIDITY OPERATING TEMPERATURE OPERATING HUMIDITY Allow for slow acclimatization after storing at extreme temperatures and humidities, to avoid condensation. Should condensation appear, leave the projector unit in a controlled environment within the operating limits until the condensation has evaporated before using the projector. 33 USER GUIDE SVGA LCD PROJECTOR 12. 2 PROJECTOR UNIT 113 x 225 x 313 (358 incl. Manual zoom and focus lens 1. 3 zoom ratio f 38-49 mm F 1. 7-2. 0 0. 65 - 7. 62 m / 25 - 300 inches (wide) 0. 48 ­ 7. 62 m / 19 - 300 inches (Tele) 1. 2 ­ 15. 6 m / 3. 9 ­ 51. 2 ft 8 - 11 degrees 120 W UHP 650 ANSI lumen 3 x 0. 9" polysilicon TFT LCD 16. 7 MILLION 300:1 800 x 600 x 3 15 (max) 12 - 150 MHz 15 - 100 KHZ 43. 5 - 130 HZ 0 - 1 Vpp 1V RMS 2 x 1 W speakers · · · · CE UL CUL FCC, Subpart J, Part 15 PROJECTOR DIMENSIONS (H x W x L) PROJECTOR WEIGHT PROJECTION LENS IMAGE SIZE PROJECTION DISTANCE ANTI-KEYSTONE CORRECTION PROJECTION LAMP LIGHT OUTPUT LIGHT VALVE COLOR RESOLUTION CONTRAST RATIO PIXEL RESOLUTION DEFECTIVE PIXELS VIDEO FREQUENCY HORIZONTAL SYNC VERTICAL SYNC COMPUTER INPUT AUDIO INPUT SPEAKERS CONFORMANCE 34 USER GUIDE SVGA LCD PROJECTOR 12. 3 POWER SUPPLY 100 - 120 VAC, 60 Hz, +/- 10 % 220 - 240 VAC, 50 Hz, +/- 10 % 200 W OPERATING, 15 W STANDBY DUAL VOLTAGE 12. 4 REMOTE CONTROL 20 x 50 x 190 mm / 0. 78 x 1. 97 x 7. 48 inch 100 g / 0. 22 lb. (with batteries) 4 pcs LR03/AAA 1. 5V penlight 15 m (50 ft) Microsoft 2-key serial; MAC; PS/2 CE, FCC UNIT SIZE (H x W x L) UNIT WEIGHT BATTERIES FUNCTIONAL RANGE COMPATIBILITY CONFORMANCE 12. 5 COMPATIBILITY The projector is compatible with the interfaces and resolutions shown below, some of which are predefined. [. . . ]