User manual ASK PROXIMA PRO AV 9300

[. . . ] 2 Register with ASK Proxima. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 Important Lamp Information. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 General Guide . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 Remote Controller General Guide . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] Whenever you want to manually trigger an input source search operation, press the [INPUT] key. When the projector detects an input source (RGB, component, or VIDEO) after an auto or manual select operation, the name of the newly selected source will appear in the projected image for a few seconds. The message "No signal input. " will appear if no input signal can be selected. Adjusting the Projected Image To adjust the size of the projected image Hold down the [ZOOM +] key to increase the size of the image or the [ZOOM ­] key to decrease it. When the image is the size you want, release the key. Projector key operation Press the [ZOOM] key and then hold down the [ ] key to increase the size of the image, press the [ZOOM] key and then hold down the [ ] key to decrease it. When the image is the size you want, release the key. To adjust image focus Hold down the [FOCUS the key. ] or [FOCUS ] key. When the focus is the way you want, release Projector key operation Press the [FOCUS] key and then hold down the [ ] or [ ] key to focus. When focus is the way you want, release the key. 13 English Projector Basics Auto Adjustment of an RGB Image When the input source is RGB (computer), the projector automatically adjusts vertical and horizontal positioning, frequency, and phase whenever it detects an RGB signal (following input source selection, power up, etc. ). You can also execute an automatic adjustment operation by pressing the [AUTO] key. You can turn off auto adjustment when you want to disable auto adjustment and maintain manual settings. The projected image may become distorted while an auto adjustment operation is in progress. If an image is unclear following the auto adjustment operation, you can use the menu to adjust items manually. Keystone Correction (KEYSTONE) When the projector is at an angle to the screen it is projecting on, the projected image may have different length top and bottom edges. This phenomenon is called, "keystoning". This projector comes with functions for automatic as well as manual keystone correction, which provides a regularly shaped projected image. Keystone correction can cause the corrected image to be smaller than the original (uncorrected) image, or it can cause distortion of the image. Indicator/Error Message POWER : Green steady TEMP :­ LAMP :­ Message : Internal temperature is too high. Description and Required Action The projector's internal temperature is very high. Press the [ESC] key to clear the warning message and perform the following steps. Check for any blocking of the projector's intake vents and exhaust vents, and make sure that there is sufficient space around the projector. If there is dust accumulated around the intake vents and/or exhaust vents, turn off the projector and remove it. 16 Troubleshooting Indicator/Error Message POWER : Amber flashing Amber steady TEMP : Red flashing (1-second interval) Turns off LAMP :­ Message : Internal temperature is too high. Description and Required Action Power has turned off automatically due to internal overheating. Check for any blocking of the projector's intake vents and exhaust vents, and make sure that there is sufficient space around the projector. If there is dust accumulated around the intake vents and/or exhaust vents, remove it. If there is no problem with the projector's vents, confirm that the POWER/STANDBY indicator is lit amber (without flashing), and then turn power back on again. If the error occurs again when you turn power back on, contact ASK Proxima service at www. askproxima. com/service Power has turned off automatically due to internal overheating. This causes a dialog box containing the text in the next item below to appear the next time you turn on the projector. [. . . ] The message "The lamp has exceeded its service life!. " is being projected. Cause and Recommended Action It is time to replace the lamp. Replace the lamp (see "Replacing the Lamp"). See Reference Guide (CD-ROM) Reference Guide (CD-ROM) The allowable life for the lamp has been exceeded, and the projector will not turn on. [. . . ]