User manual ASROCK H61M-U3S3

[. . . ] H61M/U3S3 User Manual Version 1. 0 Published February 2011 Copyright©2011 ASRock INC. All rights reserved. 1 Copyright Notice: No part of this manual may be reproduced, transcribed, transmitted, or translated in any language, in any form or by any means, except duplication of documentation by the purchaser for backup purpose, without written consent of ASRock Inc. Products and corporate names appearing in this manual may or may not be registered trademarks or copyrights of their respective companies, and are used only for identi cation or explanation and to the owners' bene t, without intent to infringe. Disclaimer: Speci cations and information contained in this manual are furnished for informational use only and subject to change without notice, and should not be constructed as a commitment by ASRock. ASRock assumes no responsibility for any errors or omissions that may appear in this manual. [. . . ] 9) SATA3_0 SATA3_1 connectors support SATA data cables for internal storage devices. The current SATA3 interface allows up to 6. 0 Gb/s data transfer rate. Either end of the SATA data cable can be connected to the SATA / SATAII / SATA3 hard disk or the SATAII / SATA3 connector on this motherboard. Besides four default USB 2. 0 ports on the I/O panel, there are two USB 2. 0 headers on this motherboard. Each USB 2. 0 header can support two USB 2. 0 ports. Serial ATA (SATA) Data Cable (Optional) USB 2. 0 Headers (9-pin USB6_7) (see p. 12 No. 15) 1 USB_PWR P-9 P+9 GND DUMMY GND P+8 P-8 USB_PWR Infrared Module Header (5-pin IR1) (see p. 12 No. 21) 1 IRTX +5VSB DUMMY This header supports an optional wireless transmitting and receiving infrared module. GND IRRX 25 Consumer Infrared Module Header (4-pin CIR1) (see p. 12 No. 18) 1 GND IRTX IRRX ATX+5VSB This header can be used to connect the remote controller receiver. This is an interface for print port cable that allows convenient connection of printer devices. Print Port Header (25-pin LPT1) (see p. 12 No. 24) 1 AFD# ERROR# PINIT# SLIN# GND SPD7 SPD6 ACK# SPD5 BUSY SPD4 PE SPD3 SLCT SPD2 SPD1 SPD0 STB# Front Panel Audio Header (9-pin HD_AUDIO1) (see p. 12 No. 26) 1 GND PRESENCE# MIC_RET OUT_RET This is an interface for front panel audio cable that allows convenient connection and control of audio devices. OUT2_L J_SENSE OUT2_R MIC2_R MIC2_L 1. High De nition Audio supports Jack Sensing, but the panel wire on the chassis must support HDA to function correctly. Please follow the instruction in our manual and chassis manual to install your system. If you use AC'97 audio panel, please install it to the front panel audio header as below: A. Connect Audio_R (RIN) to OUT2_R and Audio_L (LIN) to OUT2_L. MIC_RET and OUT_RET are for HD audio panel only. You don't need to connect them for AC'97 audio panel. For Windows® XP / XP 64-bit OS: Select "Mixer". For Windows® 7 / 7 64-bit / VistaTM / VistaTM 64-bit OS: Go to the "FrontMic" Tab in the Realtek Control panel. Adjust "Recording Volume". System Panel Header (9-pin PANEL1) (see p. 12 No. 20) This header accommodates several system front panel functions. 26 Connect the power switch, reset switch and system status indicator on the chassis to this header according to the pin assignments below. Note the positive and negative pins before connecting the cables. [. . . ] Discard Changes and Exit When you select this option, it will pop-out the following message, "Discard changes and exit setup?" Select [OK] to exit the UEFI SETUP UTILITY without saving any changes. Discard Changes When you select this option, it will pop-out the following message, "Discard changes?" Select [OK] to discard all changes. Load UEFI Defaults Load UEFI default values for all the setup questions. Launch EFI Shell from filesystem device Attempts to Launch EFI Shell application (Shell64. efi) from one of the available filesystem devices. 53 Chapter 4: Software Support 4. 1 Install Operating System This motherboard supports various Microsoft® Windows® operating systems: 7 / 7 64-bit / VistaTM / VistaTM 64-bit / XP / XP 64-bit. [. . . ]