User manual ASROCK H61TM-ITX

[. . . ] H61TM-ITX User Manual Version 1. 0 Published November 2012 Copyright©2012 ASRock INC. All rights reserved. 1 Copyright Notice: No part of this manual may be reproduced, transcribed, transmitted, or translated in any language, in any form or by any means, except duplication of documentation by the purchaser for backup purpose, without written consent of ASRock Inc. Products and corporate names appearing in this manual may or may not be registered trademarks or copyrights of their respective companies, and are used only for identification or explanation and to the owners’ benefit, without intent to infringe. Disclaimer: Specifications and information contained in this manual are furnished for informational use only and subject to change without notice, and should not be constructed as a commitment by ASRock. ASRock assumes no responsibility for any errors or omissions that may appear in this manual. [. . . ] If you plan to connect a 3-Pin CPU fan, please connect it to Pin 1-3. Serial Port Header (10-pin COM1) (see p. 14, No. 18) RI RTS GND TXD DCD 1 NC CTS DSR DTR RXD This COM1 header supports a serial port module. 28 HDMI_SPDIF Header (2-pin HDMI_SPDIF1) (see p. 14, No. 25) This header provides SPDIF audio output to HDMI VGA cards, allowing the system to connect HDMI Digital TV/projector/LCD devices. Please connect the HDMI_ SPDIF connector of a HDMI VGA card to this header. Backlight & Amp Volume Control Header (8-pin BLT_VOL1) (see p. 14, No. 17) 1 1: BKLT_EN 2: BKLT_PWM 3: BKLT_PWR 4: BKLT_PWR 5: GND 6: GND 7: Brightness_Up 8: Brightness_Down Digital MIC Header (5-pin DMIC1) (see p. 14, No. 24) 1: +5V 2: No pin 2: SPDIF_OUT/DMIC_CLK 3: GND 4: DMIC_DATA 5: +3. 3V Home Theater PC Header (7-pin HTPC1) (see p. 14, No. 29) PIN Signal Name PIN Signal Name 8 HDMI CEC 7 #Power_Button 6 SMB_DATA 5 3. 3V Standby 4 SMB_CLK 3 No pin 2 GND 1 Recording LED 29 LPC Debug Header (13-pin LPC1) (see p. 14, No. 30) PIN Signal Name 14 +3V 12 +3V 10 GND 8 LAD3 6 LAD1 4 LFRAME# 2 GND PIN Signal Name 13 No pin 11 +3V 9 GND 7 LAD2 5 LAD0 3 RESET# 1 CLK LVDS Panel Connector (40-pin LVDS1) (see p. 14, No. 15) PIN 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 Signal Name LCD_VCC LCD_VCC LCD_VCC EDID_GND EVEN_Lane0_N EVEN_Lane0_P EVEN_Lane1_N EVEN_Lane1_P EVEN_Lane2_N EVEN_Lane2_P EVEN_Lane3_N EVEN_Lane3_P ODD_Lane0_N ODD_Lane0_P ODD_Lane1_N ODD_Lane1_P ODD_Lane2_N ODD_Lane2_P ODD_Lane3_N ODD_Lane3_P PIN Signal Name 40 EDID_DATA 39 NC 38 BKLT_PWR 37 BKLT_PWR 36 BKLT_PWR 35 EVEN_CLK_N 34 EVEN_CLK_P 33 BKLT_PWM_DIM 32 BKLT_ENABLE 31 EDID_CLK 30 BKLT_GND 29 BKLT_GND 28 BKLT_GND 27 ODD_CLK_N 26 ODD_CLK_P 25 LCD_GND 24 LCD_GND 23 LCD_GND 22 EDID_3. 3V 21 NC 30 2. 9 Jumpers Setup When the jumper cap is placed on the pins, the jumper is “Short”. If no jumper cap is placed on the pins, the jumper is “Open”. The illustration shows a 3-pin jumper whose pin1 and pin2 are “Short” when a jumper cap is placed on these 2 pins. Clear CMOS Jumper (CLRCMOS1) (see p. 14, No. 31) Default Clear CMOS CLRCMOS1 allows you to clear the data in CMOS. To clear and reset the system parameters to default setup, please turn off the computer and unplug the power cord from the power supply. After waiting for 15 seconds, use a jumper cap to short pin2 and pin3 on CLRCMOS1 for 5 seconds. However, please do not clear the CMOS right after you update the BIOS. If you need to clear the CMOS when you just finish updating the BIOS, you must boot up the system first, and then shut it down before you do the clear-CMOS action. Please be noted that the password, date, time, user default profile, 1394 GUID and MAC address will be cleared only if the CMOS battery is removed. Backlight Power Jumper (3-pin BKT_PWR1) (see p. 14, No. 13) 1-2 : +19V 2-3 : +12V Panel Power Jumper (3-pin PNL_PWR1) (see p. 14, No. 14) 1-2 : +3V 2-3 : +5V 31 2. 10 Operating System Setup This motherboard supports various Microsoft® Windows® operating systems: 8 / 8 64-bit / 7 / 7 64-bit / VistaTM / VistaTM 64-bit / XP / XP 64-bit. Because motherboard settings and hardware options vary, use the setup procedures in this chapter for general reference only. Refer your OS documentation for more information. 2. 10. 1 Installing Windows® 8 / 8 64-bit / 7 / 7 64-bit / VistaTM / VistaTM 64-bit / XP / XP 64-bit without RAID Using AHCI Mode AHCI mode is not supported under Windows® XP. Press <F2> or <Delete> at system POST. [. . . ] [Fast]: When selecting “Fast”, it is not allowed to boot from a USB storage device. [Ultra Fast]: There are a few restrictions 1. Only supports Windows 8 UEFI operating system 2. You will not be able to enter BIOS Setup by using the keyboard. [. . . ]