User manual ASROCK H67M-ITX-HT

[. . . ] H67M-ITX/HT H67M-ITX User Manual Version 1. 0 Published January 2011 Copyright©2011 ASRock INC. All rights reserved. 1 Copyright Notice: No part of this manual may be reproduced, transcribed, transmitted, or translated in any language, in any form or by any means, except duplication of documentation by the purchaser for backup purpose, without written consent of ASRock Inc. Products and corporate names appearing in this manual may or may not be registered trademarks or copyrights of their respective companies, and are used only for identification or explanation and to the owners' benefit, without intent to infringe. Disclaimer: Specifications and information contained in this manual are furnished for informational use only and subject to change without notice, and should not be constructed as a commitment by ASRock. ASRock assumes no responsibility for any errors or omissions that may appear in this manual. [. . . ] If no jumper cap is placed on pins, the jumper is "Open". The illustration shows a 3-pin jumper whose pin1 and pin2 are "Short" when jumper cap is placed on these 2 pins. Jumper Clear CMOS Jumper (CLRCMOS1) (see p. 12, No. 13) Setting Description Default Clear CMOS Note: CLRCMOS1 allows you to clear the data in CMOS. To clear and reset the system parameters to default setup, please turn off the computer and unplug the power cord from the power supply. After waiting for 15 seconds, use a jumper cap to short pin2 and pin3 on CLRCMOS1 for 5 seconds. However, please do not clear the CMOS right after you update the BIOS. If you need to clear the CMOS when you just finish updating the BIOS, you must boot up the system first, and then shut it down before you do the clear-CMOS action. Please be noted that the password, date, time, user default profile, 1394 GUID and MAC address will be cleared only if the CMOS battery is removed. 29 2. 10 Onboard Headers and Connectors Onboard headers and connectors are NOT jumpers. Do NOT place jumper caps over these headers and connectors. Placing jumper caps over the headers and connectors will cause permanent damage of the motherboard! Serial ATAII Connectors SATA_2 (port 4) (SATA_2 (port 4): see p. 12/13, No. 6) SATA_3 (port 5) These two Serial ATAII (SATAII) connectors support SATA data cables for internal storage devices. The current SATAII interface allows up to 3. 0 Gb/s data transfer rate. These two Serial ATA3 (SATA3) connectors support SATA data cables for internal storage devices. The current SATA3 interface allows up to 6. 0 Gb/s data transfer rate. Either end of the SATA data cable can be connected to the SATA / SATAII / SATA3 hard disk or the SATAII / SATA3 connector on this motherboard. Besides four default USB 2. 0 ports on the I/O panel, there are two USB 2. 0 headers on this motherboard. Each USB 2. 0 header can support two USB 2. 0 ports. (SATA_0 (port 0): see p. 12/13, No. 4) Serial ATA (SATA) Data Cable (Optional) USB 2. 0 Headers (9-pin USB6_7) (see p. 12/13 No. 8) 1 USB_PWR P-9 P+9 GND DUMMY GND P+8 P-8 USB_PWR Consumer Infrared Module Header (4-pin CIR1) (see p. 12/13 No. 9) 1 GND IRTX IRRX ATX+5VSB SATA_0 (port 0) SATA_1 (port 1) Serial ATA3 Connectors This header can be used to connect the remote controller receiver. 30 Front Panel Audio Header (9-pin HD_AUDIO1) (see p. 12 No. 18) 1 GND PRESENCE# MIC_RET OUT_RET This is an interface for front panel audio cable that allows convenient connection and control of audio devices. OUT2_L J_SENSE OUT2_R MIC2_R MIC2_L 1. [. . . ] Discard Changes and Exit When you select this option, it will pop-out the following message, "Discard changes and exit setup?" Select [OK] to exit the UEFI SETUP UTILITY without saving any changes. Discard Changes When you select this option, it will pop-out the following message, "Discard changes?" Select [OK] to discard all changes. Load UEFI Defaults Load UEFI default values for all the setup questions. Launch EFI Shell from filesystem device Attempts to Launch EFI Shell application (Shell64. efi) from one of the available filesystem devices. 59 Chapter 4: Software Support 4. 1 Install Operating System This motherboard supports various Microsoft® Windows® operating systems: 7 / 7 64-bit / VistaTM / VistaTM 64-bit / XP / XP 64-bit. [. . . ]