User manual ASROCK H77 PRO4MVP

[. . . ] H77 Pro4/MVP User Manual Version 1. 2 Published June 2013 Copyright©2013 ASRock INC. All rights reserved. 1 Copyright Notice: No part of this manual may be reproduced, transcribed, transmitted, or translated in any language, in any form or by any means, except duplication of documentation by the purchaser for backup purpose, without written consent of ASRock Inc. Products and corporate names appearing in this manual may or may not be registered trademarks or copyrights of their respective companies, and are used only for identification or explanation and to the owners’ benefit, without intent to infringe. Disclaimer: Specifications and information contained in this manual are furnished for informational use only and subject to change without notice, and should not be constructed as a commitment by ASRock. ASRock assumes no responsibility for any errors or omissions that may appear in this manual. [. . . ] Please be noted that the password, date, time, user default profile, 1394 GUID and MAC address will be cleared only if the CMOS battery is removed. 31 2. 11 Onboard Headers and Connectors Onboard headers and connectors are NOT jumpers. Do NOT place jumper caps over these headers and connectors. Placing jumper caps over the headers and connectors will cause permanent damage of the motherboard! Serial ATA2 Connectors (SATA2_2: see p. 13, No. 18) These four Serial ATA2 (SATA2) connectors support SATA data cables for internal storage devices. The current SATA2 interface allows up to 3. 0 Gb/s data transfer rate. SATA2_4 Serial ATA3 Connectors (SATA3_0: see p. 13, No. 9) SATA3_1 SATA2_2 SATA2_5 SATA2_3 SATA3_0 SATA3_A2 SATA3_A1 These four Serial ATA3 (SATA3) connectors support SATA data cables for internal storage devices. The current SATA3 interface allows up to 6. 0 Gb/s data transfer rate. Serial ATA (SATA) Data Cable (Optional) Either end of the SATA data cable can be connected to the SATA / SATA2 / SATA3 hard disk or the SATA2 / SATA3 connector on this motherboard. USB 2. 0 Headers Besides six default USB 2. 0 (9-pin USB_6_7) ports on the I/O panel, there are (see p. 13, No. 23) two USB 2. 0 headers on this motherboard. Each USB 2. 0 header can support two USB 2. 0 ports. 32 (9-pin USB_8_9) (see p. 13, No. 24) USB 3. 0 Header Besides two default USB 3. 0 (19-pin USB3_0_1) ports on the I/O panel, there is (see p. 13, No. 10) one USB 3. 0 header on this motherboard. This USB 3. 0 header can support two USB 3. 0 ports. Infrared Module Header (5-pin IR1) (see p. 13, No. 26) This header supports an optional wireless transmitting and receiving infrared module. Consumer Infrared Module Header This header can be used to (4-pin CIR1) connect the remote controller (see p. 13, No. 25) receiver. Front Panel Audio Header (9-pin HD_AUDIO1) (see p. 13, No. 30) This is an interface for front panel audio cable that allows convenient connection and control of audio devices. 33 1. High Definition Audio supports Jack Sensing, but the panel wire on the chassis must support HDA to function correctly. Please follow the instruction in our manual and chassis manual to install your system. If you use AC’97 audio panel, please install it to the front panel audio header as below: A. Connect Audio_R (RIN) to OUT2_R and Audio_L (LIN) to OUT2_L. MIC_RET and OUT_RET are for HD audio panel only. You don’t need to connect them for AC’97 audio panel. For Windows® XP / XP 64-bit OS: Select “Mixer”. [. . . ] Then choose the directory (xx\AMD64\) you have copied in the first step. 69 E. Please keep the USB flash disk installed until the system's first reboot. Continue to install OS by following the Windows® instructions. Follow Windows® Installation Guide to install OS. [. . . ]