User manual ASROCK H77M

[. . . ] H77M User Manual Version 1. 2 Published May 2013 Copyright©2013 ASRock INC. All rights reserved. 1 Copyright Notice: No part of this manual may be reproduced, transcribed, transmitted, or translated in any language, in any form or by any means, except duplication of documentation by the purchaser for backup purpose, without written consent of ASRock Inc. Products and corporate names appearing in this manual may or may not be registered trademarks or copyrights of their respective companies, and are used only for identification or explanation and to the owners’ benefit, without intent to infringe. Disclaimer: Specifications and information contained in this manual are furnished for informational use only and subject to change without notice, and should not be constructed as a commitment by ASRock. ASRock assumes no responsibility for any errors or omissions that may appear in this manual. [. . . ] 8) Serial ATA (SATA) Data Cable (Optional) USB 2. 0 Headers (9-pin USB6_7) (see p. 13, No. 19) (9-pin USB8_9) (see p. 13, No. 21) These four Serial ATA2 (SATA2) connectors support SATA data cables for internal storage devices. The current SATA2 interface allows up to 3. 0 Gb/s data transfer rate. These two Serial ATA3 (SATA3) connectors support SATA data cables for internal storage devices. The current SATA3 interface allows up to 6. 0 Gb/s data transfer rate. Either end of the SATA data cable can be connected to the SATA / SATA2 / SATA3 hard disk or the SATA2 / SATA3 connector on this motherboard. Besides six default USB 2. 0 ports on the I/O panel, there are two USB 2. 0 headers on this motherboard. Each USB 2. 0 header can support two USB 2. 0 ports. SATA2_5 SATA2_4 SATA2_3 SATA3_1 SATA3_0 USB_PWR P-9 P+9 GND DUMMY 1 GND P+8 P-8 USB_PWR 31 SATA2_2 USB 3. 0 Header (19-pin USB3_0_1) (see p. 13, No. 7) IntA_P0_D+ IntA_P0_DGND IntA_P0_SSTX+ IntA_P0_SSTXGND IntA_P0_SSRX+ IntA_P0_SSRXVbus 1 Vbus IntA_P1_SSRXIntA_P1_SSRX+ GND IntA_P1_SSTXIntA_P1_SSTX+ GND IntA_P1_DIntA_P1_D+ DUMMY Besides two default USB 3. 0 ports on the I/O panel, there is one USB 3. 0 header on this motherboard. This USB 3. 0 header can support two USB 3. 0 ports. Infrared Module Header (5-pin IR1) (see p. 13, No. 25) This header supports an optional wireless transmitting and receiving infrared module. Consumer Infrared Module Header (4-pin CIR1) (see p. 13 No. 20) Print Port Header (25-pin LPT1) (see p. 13 No. 23) AFD# ERROR# PINIT# SLIN# This header can be used to connect the remote controller receiver. This is an interface for print port cable that allows convenient connection of printer devices. GND 1 SPD7 SPD6 ACK# SPD5 BUSY SPD4 PE SPD3 SLCT SPD2 SPD1 SPD0 STB# Front Panel Audio Header (9-pin HD_AUDIO1) (see p. 13, No. 30) GND PRESENCE# MIC_RET OUT_RET 1 OUT2_L J_SENSE OUT2_R MIC2_R MIC2_L This is an interface for front panel audio cable that allows convenient connection and control of audio devices. 1. High Definition Audio supports Jack Sensing, but the panel wire on the chassis must support HDA to function correctly. Please follow the instruction in our manual and chassis manual to install your system. If you use AC’97 audio panel, please install it to the front panel audio header as below: A. Connect Audio_R (RIN) to OUT2_R and Audio_L (LIN) to OUT2_L. Connect Ground (GND) to Ground (GND). 32 D. MIC_RET and OUT_RET are for HD audio panel only. [. . . ] Then choose the directory (xx\AMD64\) you have copied in the first step. 65 E. Please keep the USB flash disk installed until the system's first reboot. Continue to install OS by following the Windows® instructions. Follow Windows® Installation Guide to install OS. [. . . ]