User manual ASROCK IMB-171-L

[. . . ] With respect to the contents of this manual, ASRock does not provide warranty of any kind, either expressed or implied, including but not limited to the implied warranties or conditions of merchantability or fitness for a particular purpose. In no event shall ASRock, its directors, officers, employees, or agents be liable for any indirect, special, incidental, or consequential damages (including damages for loss of profits, loss of business, loss of data, interruption of business and the like), even if ASRock has been advised of the possibility of such damages arising from any defect or error in the manual or product. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. CALIFORNIA, USA ONLY The Lithium battery adopted on this motherboard contains Perchlorate, a toxic substance controlled in Perchlorate Best Management Practices (BMP) regulations passed by the California Legislature. [. . . ] Though this motherboard provides a 4-Pin CPU fan (Quiet Fan) connector, 3-Pin CPU fans can still work successfully even without fan speed control. If you plan to connect a 3-Pin CPU fan, please connect it to Pin 1-3. CPU Fan Connector (4-pin CPU_FAN1) (see p. 10, No. 5) GND +12V CPU_FAN_SPEED FAN_SPEED_CONTROL 18 Serial Port Header (10-pin COM4) (see p. 10, No. 21) PIN 1 2 3 4 5 2 PIN Signal Name PIN Signal Name 2 4 6 8 10 NC CTS DSR DTR RXD 1 3 5 7 9 COM VOLT RTS GND TXD DCD 1 RS232 DCD, Data carrier detect RXD, Receive data TXD, Transmit data DTR, Data terminal ready GND RS422 TX+ RXTXRX+ GND RS485 RTX+ N/A RTXN/A GND LVDS Connector (40-pin LVDS1) (see p. 10, No. 2) 39 40 PIN 39 37 35 33 31 29 27 25 23 21 19 17 15 13 11 9 7 5 3 1 Signal Name GND LVDS2 D3(-) LVDS2 CLK(-) LVDS2 D2(-) LVDS2 D1(-) LVDS2 D0(-) GND LVDS1 D3(-) LVDS1 CLK(-) LVDS1 D2(-) LVDS1 D1(-) LVDS1 D0(-) B/L ENABLE B/L ADJUST DDC CLK LVDS PWR VCC 3. 3V +12V +12V +12V PIN 40 38 36 34 32 30 28 26 24 22 20 18 16 14 12 10 8 6 4 2 Signal Name GND LVDS2 D3(+) LVDS2 CLK(+) LVDS2 D2(+) LVDS2 D1(+) LVDS2 D0(+) GND LVDS1 D3(+) LVDS1 CLK(+) LVDS1 D2(+) LVDS1 D1(+) LVDS1 D0(+) GND LVDS PWR EN DDC DATA LVDS PWR GND GND +12V +12V 1 2 19 Inverter Power Control Connector (5-pin BLT_PWR3) (see p. 10, No. 4) PIN 1 Signal Name +12V GND B/L ENABLE B/L ADJUST +5V 1 2 3 4 5 Backlight & Amp Volume Control Header (7-pin BLT_VOL1) (see p. 10, No. 1) PIN 1 Signal Name VOL_UP VOL_DW BKT_OFF BKT_UP BKT_DW GND GND 1 2 3 4 5 6 7 GPIO&AMP Header (10-pin DGIO_AMP1) (see p. 10, No. 22) 2 PIN Signal Name 2 4 6 8 10 SMB_DATA GPO[1] GPO[0] AMP R(-) AMP R(+) PIN Signal Name 1 3 5 7 9 SMB_CLK GPI[1] GPI[0] AMP L(-) AMP L(+) 1 Internal Speaker Header (4-pin SPEAKER1) (see p. 10, No. 27) 1 SPK_RSPK_R+ SPK_LSPK_L+ 20 VGA Header (10-pin VGA_H1) (see p. 10, No. 28) 1 2 PIN Signal Name PIN Signal Name 9 7 5 3 1 RED GRN BLUE HSYNC DDC_CLK 10 8 6 4 2 GND GND GND VSYNC DDC_DAT 21 2. 7 Jumpers Setup The illustration shows how jumpers are setup. When the jumper cap is placed on the pins, the jumper is “Short”. The CD automatically displays the Main Menu if “AUTORUN” is enabled in your computer. If the Main Menu does not appear automatically, locate and double click on the file “ASRSETUP. EXE” in the Support CD to display the menu. 2. 9. 2 Drivers Menu The drivers compatible to your system will be auto-detected and listed on the support CD driver page. Please follow the order from top to bottom to install those required drivers. Therefore, the drivers you install can work properly. 2. 9. 3 Utilities Menu The Utilities Menu shows the application softwares that the motherboard supports. Click on a specific item then follow the installation wizard to install it. 2. 9. 4 Contact Information If you need to contact ASRock or want to know more about ASRock, you’re welcome to visit ASRock’s website at http://www. asrock. com; or you may contact your dealer for further information. 25 2. 10 Hot Plug for Hard Disk Drives This motherboard supports Hot Plug for SATA2 in AHCI mode. What is Hot Plug? If the HDDs are NOT set for RAID, it is called “Hot Plug” for the action to insert and remove the HDDs while the system is still powered on and in working condition. However, please note that it cannot perform Hot Plug if the OS has been installed into the HDD. Hot Plug Operation Guide Please read the operation guide of Hot Plug below carefully. Before you process Hot Plug, please check the cable accessories from the motherboard gift box pack below. [. . . ] WDT Timeout Reset This allows users to enable or disable the Watch Dog Timer timeout to reset the system. 38 3. 3. 5 ACPI Configuration Suspend to RAM Use this to select whether to auto-detect or disable Suspend-toRAM. Select [Auto] to enable if the OS supports it. S3 Video Repost Use this to enable/disable S3 Video Repost. PS/2 Keyboard Power On Use this to enable or disable the PS/2 keyboard to turn on the system from power-soft-off mode. [. . . ]