User manual ASROCK IMB-A160

[. . . ] IMB-A160 User Manual Version 1. 0 Published October 2012 Copyright©2012 ASRock INC. All rights reserved. 1 Copyright Notice: No part of this manual may be reproduced, transcribed, transmitted, or translated in any language, in any form or by any means, except duplication of documentation by the purchaser for backup purpose, without written consent of ASRock Inc. Products and corporate names appearing in this manual may or may not be registered trademarks or copyrights of their respective companies, and are used only for identification or explanation and to the owners’ benefit, without intent to infringe. Disclaimer: Specifications and information contained in this manual are furnished for informational use only and subject to change without notice, and should not be constructed as a commitment by ASRock. ASRock assumes no responsibility for any errors or omissions that may appear in this manual. [. . . ] 34) 1 PIN 1 2 3 4 Signal Name SPK L+ SPK LSPK RSPK R+ Chassis Fan Connector (3-pin CHA_FAN1) (see p. 10, No. 38) GND +12V FAN_SPEED Please connect a fan cable to the fan connector and match the black wire to the ground pin. 20 CPU Fan Connector (4-pin CPU_FAN1) (see p. 10, No. 7) FAN_SPEED_CONTROL FAN_SPEED +12V GND Though this motherboard provides a 4-Pin CPU fan (Quiet Fan) connector, 3-Pin CPU fans can still work successfully even without fan speed control. If you plan to connect a 3-Pin CPU fan, please connect it to Pin 1-3. 1 2 3 4 Serial Port Header (9-pin COM3) (see p. 10, No. 22) 1 RRXD1 DDTR#1 DDSR#1 CCTS#1 These COM headers support serial port modules. RRI#1 RRTS#1 GND TTXD1 DDCD#1 TPM Header (17-pin TPM1) (see p. 10, No. 36) F_CLKRUN# SERIRQ# S_PWRDWN# GND LAD1_L LAD2_L SMB_DATA_MAIN SMB_CLK_MAIN GND 1 GND +3VSB This connector supports Trusted Platform Module (TPM) system, which can securely store keys, digital certificates, passwords, and data. A TPM system also helps enhance network security, protects digital identities, and ensures platform integrity. LAD0_L +3V LAD3_L TPM_RST# LFRAME#_L CK_33M_TPM 21 LVDS Connector (Optional) (40-pin LVDS1) (see p. 10, No. 2) 1 39 2 40 PIN 2 4 6 8 10 12 14 16 18 20 22 24 26 28 30 32 34 36 38 40 Signal Name LVDS_PWR DDC CLK LVDS1 D0(-) GND LVDS1 D1(+) LVDS1 D2(-) GND LVDS1 D3(+) LVDS1 CLK(-) GND LVDS2 D0(+) LVDS2 D1(-) GND LVDS2 D2(+) LVDS2 D3(-) GND LVDS2 CLK(+) B/L ENABLE BLT_PWR BLT_PWR PIN 1 3 5 7 9 11 13 15 17 19 21 23 25 27 29 31 33 35 37 39 Signal Name LVDS_PWR +3V DDC DATA LVDS1 D0(+) LVDS1 D1(-) GND LVDS1 D2(+) LVDS1 D3(-) GND LVDS1 CLK(+) LVDS2 D0(-) GND LVDS2 D1(+) LVDS2 D2(-) LVDS PWR EN LVDS2 D3(+) LVDS2 CLK(-) GND B/L ADJUST BLT_PWR Inverter Power Control Header (Optional) (6-pin BLT_PWR2) (see p. 10, No. 4) 1 1, 2: GND 3: Panel Backlight Control 4: Panel Backlight Enable 5, 6: Panel Backlight Power Backlight & Amp Volume Control Header (Optional) (7-pin BLT_VOL1) (see p. 10, No. 6) 1 1: Volume_UP 2: Volume_DOWN 3: PANEL PWR Down 4: Panel BackLight UP 5: Panel BackLight Down 6: GND 7: GND 22 Digital I/O Header (10-pin DIO1) (see p. 10, No. 25) 1 PIN Signal Name 1 GP4 3 GP5 5 GP6 7 GP7 9 +5V PIN Signal Name 2 GP0 4 GP1 6 GP2 8 GP3 10 GND mini SATA Connector (M_SATA1) (see p. 10, No. 1) This mini SATA connector can be used to connect a Solid-State Drive (SSD) for an internal storage device. Or used for USB interface addon cards. 23 2. 7 Jumpers Setup The illustration shows how jumpers are setup. When the jumper cap is placed on the pins, the jumper is “Short”. If no jumper cap is placed on the pins, the jumper is “Open”. The illustration shows a 3-pin jumper whose pin1 and pin2 are “Short” when a jumper cap is placed on these 2 pins. Clear CMOS Jumper (3-pin CLRCMOS1) (see p. 10, No. 27) Default Clear CMOS CLRCMOS1 allows you to clear the data in CMOS. To clear and reset the system parameters to default setup, please turn off the computer and unplug the power cord from the power supply. After waiting for 15 seconds, use a jumper cap to short pin2 and pin3 on CLRCMOS1 for 5 seconds. However, please do not clear the CMOS right after you update the BIOS. If you need to clear the CMOS when you just finish updating the BIOS, you must boot up the system first, and then shut it down before you do the clear-CMOS action. Please be noted that the password, date, time, user default profile, 1394 GUID and MAC address will be cleared only if the CMOS battery is removed. Backlight Power Jumper (3-pin BKT_PWR1) (see p. 10, No. [. . . ] Ring-In Power On Use this to enable or disable the Ring-In signals to turn on the system from power-soft-off mode. RTC Alarm Power On 43 Use this to enable or disable the RTC (Real Time Clock) to power on the system. USB Keyboard/Remote Power On Use this to enable or disable the USB Keyboard/Remote to power on the system. USB Mouse Power On Use this to enable or disable the USB Mouse to power on the system. 44 3. 3. 7 USB Configuration USB 2. 0 Controller Use this to enable or disable the USB 2. 0 controller. [. . . ]