User manual ASROCK K8S8X

[. . . ] K8S8X User Manual Version 1. 02 Published May 2004 Copyright©2004 ASRock INC. All rights reserved. 1 Copyright Notice: No part of this manual may be reproduced, transcribed, transmitted, or translated in any language, in any form or by any means, except duplication of documentation by the purchaser for backup purpose, without written consent of ASRock Inc. Products and corporate names appearing in this manual may or may not be registered trademarks or copyrights of their respective companies, and are used only for identification or explanation and to the owners' benefit, without intent to infringe. Disclaimer: Specifications and information contained in this manual are furnished for informational use only and subject to change without notice, and should not be constructed as a commitment by ASRock. ASRock assumes no responsibility for any errors or omissions that may appear in this manual. [. . . ] 15) 1 PLED+ PLEDPWRBTN# GND This header accommodates several system front panel functions. DUMMY RESET# GND HDLEDHDLED+ Chassis Speaker Header (4-pin SPEAKER 1) (see p. 8, No. 17) 1 SPEAKER DUMMY DUMMY +5V Please connect the chassis speaker to this header. Chassis Fan Connector (3-pin CHA_FAN1) (see p. 8, No. 14) GND +12V CHA_FAN_SPEED Please connect the chassis fan cable to this connector and match the black wire to the ground pin. Please connect the CPU fan cable to this connector and match the black wire to the ground pin. Connect a Game cable to this connector if the Game port bracket is installed. CPU Fan Connector (3-pin CPU_FAN1) (see p. 8, No. 1) GND +12V CPU_FAN_SPEED Game Connector (15-pin GAME1) (see p. 8, No. 20) 1 +5V JBB1 JBX MIDI_OUT JBY JBB2 MIDI_IN +5V JAB2 JAY GND GND JAX JAB1 +5V Power LED Connector (3-pin PWRLED1) (see p. 8, No. 16) 1 PLEDPLED+ PLED+ Please connect a 3-pin power LED cable to this connector. ATX Power Connector (20-pin ATXPWR1) (see p. 8, No. 24) Please connect an ATX power supply to this connector. ATX 12V Connector (4-pin U74) (see p. 8, No. 5) Please connect an ATX 12V power supply to this connector. 17 2. 7 Serial ATA (SATA) Hard Disks Installation This motherboard adopts SiS 964 southbridge chipset that supports Serial ATA (SATA) hard disks and RAID functions. You may install SATA hard disks on this motherboard for internal storage devices. This section will guide you to install the SATA hard disks. STEP 1: Install the SATA hard disks into the drive bays of your chassis. STEP 2: Connect one end of the SATA data cable to the motherboard's primary SATA connector (SATA1). STEP 3: Connect the other end of the SATA data cable to the primary SATA hard disk. STEP 4: Connect the SATA power cable to the SATA hard disk. If you just want to install only one SATA HDD, the installation process is complete at this step. If you want to install two SATA HDDs or you want to use RAID function, please continue to do the following steps. STEP 5: Connect one end of the second SATA data cable to the motherboard's secondary SATA connector (SATA2). STEP 6: Connect the other end of the SATA data cable to the secondary SATA hard disk. STEP 7: Connect the SATA power cable to the SATA hard disk. 2. 8 Hot Plug and Hot Swap Functions for SATA HDDs K8S8X motherboard supports Hot Plug function for SATA Devices. Usually, each power wire will provide 2 power connectors for HDDs. [. . . ] Configuration options: [Auto], [2CLK], [3CLK], [4CLK], [5CLK], and [6CLK]. Configuration options: [Auto], [5CLK], [6CLK], [7CLK], [8CLK], [9CLK], [10CLK], [11CLK], and [12CLK]. Configuration options: [Auto], [2CLK], [3CLK], [4CLK], [5CLK], and [6CLK]. 3. 7. 2 South Bridge Configuration BIOS SETUP UTILITY Chipset SouthBridge Chipset Configuration Onboard Ac97 Audio Onboard LAN [Auto] [Enabled] Enable / Disable onboard Audio device. +F1 F9 F10 ESC Select Screen Select Item Change Option General Help Load Defaults Save and Exit Exit v02. 54 (C) Copyright 1985-2003, American Megatrends, Inc. OnBoard AC'97 Audio Select [Disabled], [Auto] or [Enabled] for the onboard AC'97 Audio feature. OnBoard LAN Use this item to enable or disable the onboard LAN device. 33 3. 7. 3 AGP Configuration BIOS SETUP UTILITY Chipset AGP Chipset Configuration AGP Aperture Size AGP Data Rate AGP Fast Write Primary Graphics Adapter [64 MB] [8X] [Disabled] [PCI] Aperture size defines a Window into system memory for the AGP video controller. [. . . ]