User manual ASROCK P4I65PE

[. . . ] P4i65PE User Manual Version 1. 1 Published May 2005 Copyright©2005 ASRock INC. All rights reserved. 1 Copyright Notice: No part of this manual may be reproduced, transcribed, transmitted, or translated in any language, in any form or by any means, except duplication of documentation by the purchaser for backup purpose, without written consent of ASRock Inc. Products and corporate names appearing in this manual may or may not be registered trademarks or copyrights of their respective companies, and are used only for identification or explanation and to the owners' benefit, without intent to infringe. Disclaimer: Specifications and information contained in this manual are furnished for informational use only and subject to change without notice, and should not be constructed as a commitment by ASRock. ASRock assumes no responsibility for any errors or omissions that may appear in this manual. [. . . ] 19) 1 USB_PWR P-6 P+6 GND DUMMY GND P+7 P-7 USB_PWR USB 2. 0 Header (9-pin USB45) (see p. 8, No. 20) 1 USB_PWR P-5 P+5 GND DUMMY GND P+4 P-4 USB_PWR Infrared Module Header (5-pin IR1) (see p. 8, No. 18) 1 IRTX +5V CCIRRX GND IRRX Internal Audio Connectors (4-pin CD1) (CD1: see p. 8, No. 28) CD-R GND GND CD-L CD1 These connectors allow you to receive stereo audio input from sound sources such as a CD-ROM, DVD-ROM, TV tuner card, or MPEG card. This is an interface for the front panel audio cable that allows convenient connection and control of audio devices. Front Panel Audio Header (9-pin AUDIO1) (see p. 8, No. 24) 1 GND +5VA BACKOUT-R BACKOUT-L AUD-OUT-L GND AUD-OUT-R MIC-POWER MIC 17 System Panel Header (9-pin PANEL1) (see p. 8 No. 16) 1 PLED+ PLEDPWRBTN# GND This header accommodates several system front panel functions. DUMMY RESET# GND HDLEDHDLED+ Chassis Speaker Header (4-pin SPEAKER 1) (see p. 8 No. 17) 1 SPEAKER DUMMY DUMMY +5V Please connect the chassis speaker to this header. Chassis Fan Connector (3-pin CHA_FAN1) (see p. 8 No. 14) GND +12V CHA_FAN_SPEED Please connect a chassis fan cable to this connector and match the black wire to the ground pin. Please connect a CPU fan cable CPU Fan Connector (3-pin CPU_FAN1) (see p. 8 No. 2) GND +12V CPU_FAN_SPEED to this connector and match the black wire to the ground pin. Please connect an ATX power supply to this connector. ATX Power Connector (20-pin ATXPWR1) (see p. 8 No. 29) Game Port Connector (15-pin GAME1) (see p. 8 No. 22) 1 +5V JBB1 JBX MIDI_OUT JBY JBB2 MIDI_IN Connect a Game cable to this connector if the Game port bracket is installed. +5V JAB2 JAY GND GND JAX JAB1 +5V ATX 12V Connector (4-pin ATX12V1) (see p. 8, No. 7) Please note that it is necessary to connect a power supply with ATX 12V plug to this connector so that it can provides sufficient power. Failing to do so will cause the failure to power up. 18 2. 7 AT (SAT Serial ATA (SATA) Hard Disks Installation This motherboard adopts Intel ICH5 south bridge chipset that supports Serial ATA (SATA) hard disks. You may install SATA hard disks on this motherboard for internal storage devices. This section will guide you to install the SATA hard disks. STEP 1: Install the SATA hard disks into the drive bays of your chassis. STEP 2: Connect the SATA power cable to the SATA hard disk. STEP 3: Connect one end of the SATA data cable to the motherboard's primary SATA connector (SATA1). STEP 4: Connect the other end of the SATA data cable to the primary SATA hard disk. [. . . ] Configuration options: [DMA0], [DMA1], and [DMA3]. Parallel Port IRQ Use this item to set the IRQ for the parallel port. Configuration options: [IRQ5] and [IRQ7]. OnBoard Game Port Use this item to enable the Game Port or disable it. [. . . ]